Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock Function does not Operate

for Preparation Click here


DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the lock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for front passenger side electrical key antenna)).

WIRING DIAGRAM


B312718E04


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  5. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) (Click here)
OK


2.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Entry & Start / Data List.

  1. Read the Data List according to the display on the GTS.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Door Trigger Switch
    Front door outside handle assembly (for front passenger side) (unlock sensor) / OFF or ON
    OFF: Front door outside handle assembly (for passenger side) (unlock sensor) not touched
    ON: Front door outside handle assembly (for passenger side) (unlock sensor) touched
    1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

    OK:
    On the GTS screen, the display changes between ON and OFF as shown in the table above.



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY)
  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the F5*1 or E1*2 front door outside handle assembly (for driver side door) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D41-8 (TSW2) - F5-1 (TRG+)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-8 (TSW2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D41-8 (TSW2) - E1-1 (TRG+)
    Always
    Below 1 Ω
    D48-11 (GND) - Body ground
    Always
    Below 1 Ω
    D41-8 (TSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)
  1. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  1. Reconnect the F5*1 or E1*2 front door outside handle assembly connector.

    1. *1: for LHD
    2. *2: for RHD



  1. Using an oscilloscope, check the waveform.


    B271429E03


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    *b
    Waveform
    *c
    Passenger side door lock sensor touched
    -
    -

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    D41-8 (TSW2) - D48-11 (GND)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Passenger side door lock sensor not touched → touched
    2 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform)



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)