Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System)

DTC    B1409    SCU Communication Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) stores this code if a communication problem is detected between the main body ECU (network gateway ECU) and the transponder key ECU assembly.

DTC Code
DTC Detection Condition
Trouble Area
B1409
When there is a problem in communication between the main body ECU (network gateway ECU) and the transponder key ECU assembly.
  1. Harness or connector
  2. Main body ECU (network gateway ECU)
  3. Transponder key ECU assembly

WIRING DIAGRAM


B317021E02


INSPECTION PROCEDURE

NOTICE:
  1. If the main body ECU (network gateway ECU) or transponder key ECU assembly is replaced, refer to Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY, BODY GROUND)
  1. Disconnect the A73 and D6 main body ECU (network gateway ECU) connectors.

  1. Disconnect the 3A, 3B and 3C instrument panel junction block assembly connectors.



    B317020E01
  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
3A-27 - Body ground
Always
11 to 14 V
3C-19 - Body ground
Always
11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
3B-18 - Body ground
Always
Below 1 Ω
A73-4 (GND) - Body ground
Always
Below 1 Ω
D6-1 (GND) - Body ground
Always
Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.


B312643E02


Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-

Standard Resistance:

Tester Connection
Condition
Specified Condition
MB-1 (BECU) - 3A-27
Always
Below 1 Ω
MB-32 (BMPX) - 3C-19
Always
Below 1 Ω
MB-11 (GND) - 3B-18
Always
Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY, BODY GROUND)
  1. Disconnect the A64 transponder key ECU assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
A64-1 (+B) - Body ground
Always
11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
A64-5 (GND) - Body ground
Always
Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - TRANSPONDER KEY ECU ASSEMBLY)
  1. Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
A73-17 (UART) - Body ground
Always
Below 1 V

Standard Resistance:
Tester Connection
Condition
Specified Condition
A73-17 (UART) - A64-3 (UART)
Always
Below 1 Ω
A73-17 (UART) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

OK:
DTC B1409 is not output



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)