Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR

POWER WINDOW REGULATOR MOTOR > INSTALLATION

for Preparation Click here


HINT:
Use the same procedure for the RH side and LH side.



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. Install the temporary bolt to the front door window regulator sub-assembly.



    B314800E01
  1. Temporarily install the front door window regulator sub-assembly.

  1. Tighten the 3 bolts and 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Tighten the temporary bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.
    Text in Illustration 
    *1
    Temporary Bolt



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Check the front door glass sub-assembly .

  1. Adjust the front door glass sub-assembly .



4. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
  1. Install the front door rear lower frame sub-assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



5. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



  1. Pass the front door lock remote control cable assembly and the front door inside locking cable assembly through a new front door service hole cover.


    B314821E01


    Text in Illustration 
    *1
    Reference Point
    -
    -

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    1. Overlay the butyl tape in lengths of 20 cm (7.874 in.) or more.
    2. Do not block the drip holes in the front door panel with butyl tape.
    3. Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Connect each connector.



6. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B314154
  1. Install the power window regulator master switch assembly with front door armrest base panel with the 4 screws.



7. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B314155
  1. Install the power window regulator switch assembly with front door armrest base panel with the 4 screws.



8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B313122E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. Connect each connector.



    B314824
  1. Engage the 10 clips and install the front door trim board sub-assembly.



    B313120
  1. Engage the clip and install the 3 screws.



    B314825
  1. Engage the claw and install the cap.



9. INSTALL DOOR ARMREST COVER


    B314960
  1. Engage the guide and 7 claws, and install the door armrest cover.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



11. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


12. INSPECT POWER WINDOW OPERATION
(Click here)