Home › Engine / Hybrid System › FA20 COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

  1. w/ Air Conditioning System
    The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning (ON/OFF), air conditioner refrigerant pressure, engine speed and vehicle speed signals.
The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.
  1. w/o Air Conditioning System
    The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, engine speed and vehicle speed signals.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.

  1. Check the operation of the cooling fans while operating them using the GTS.

    OK:

    Tester Operation
    Specified Condition
    ON
    Cooling fans operate
    OFF
    Cooling fans stop


    Result:

    Result
    Proceed to
    OK
    A
    NG (w/o Air Conditioning System)
    B
    NG (w/ Air Conditioning System)
    C



B
Go to step 2

C
Go to step 9
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)


    A280291E01
  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (FAN No. 1 relay terminal) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 1 Relay Terminals

  1. Reinstall the FAN No. 1 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 1 RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY)


    A280291E01
  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (FAN No. 1 relay terminal) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 1 Relay Terminals

  1. Reinstall the FAN No. 1 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY)
OK


4.INSPECT FAN NO. 1 RELAY
  1. Inspect the FAN No. 1 relay .



NG
REPLACE FAN NO. 1 RELAY
OK


5.INSPECT COOLING FAN MOTOR
  1. Inspect the cooling fan motor .



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
  1. Disconnect the A45 cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A45-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the A45 cooling fan motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
OK


7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the A45 cooling fan motor connector.

  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A45-2 - 3 (FAN No. 1 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A45-2 or 3 (FAN No. 1 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A45 cooling fan motor connector.

  1. Reinstall the FAN No. 1 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
OK


8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the A35 ECM connector.

  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A35-11 (FAN1) - 1 (FAN No. 1 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A35-11 (FAN1) or 1 (FAN No. 1 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A35 ECM connector.

  1. Reinstall the FAN No. 1relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
OK

REPLACE ECM (Click here)  

9.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)


    A280291E01
  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (FAN No. 1 relay terminal) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 1 Relay Terminals

  1. Reinstall the FAN No. 1 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 1 RELAY)
OK


10.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 3 RELAY VOLTAGE)


    A280292E01
  1. Remove the FAN No. 3 relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (FAN No. 3 relay terminal) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 3 Relay Terminals

  1. Reinstall the FAN No. 3 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 3 RELAY)
OK


11.CHECK HARNESS AND CONNECTOR (FAN NO. 1, NO. 2 OR NO. 3 RELAY)


    A280293E01
  1. Remove the FAN No. 1, FAN No. 2 and FAN No. 3 relays from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (FAN No. 1 relay terminal) - Body ground
    Ignition switch ON
    11 to 14 V
    1 (FAN No. 2 relay terminal) - Body ground
    Ignition switch ON
    11 to 14 V
    2 (FAN No. 3 relay terminal) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 1 Relay Terminals
    *3
    FAN No. 2 Relay Terminals
    *4
    FAN No. 3 Relay Terminals

  1. Reinstall the FAN No. 1, FAN No. 2 and FAN No. 3 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1, NO. 2 OR NO. 3 RELAY)
OK


12.INSPECT FAN NO. 1 RELAY
  1. Inspect the FAN No. 1 relay .



NG
REPLACE FAN NO. 1 RELAY
OK


13.INSPECT FAN NO. 2 RELAY
  1. Inspect the FAN No. 2 relay .



NG
REPLACE FAN NO. 2 RELAY
OK


14.INSPECT FAN NO. 3 RELAY
  1. Inspect the FAN No. 3 relay .



NG
REPLACE FAN NO. 3 RELAY
OK


15.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
  1. Remove the FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    5 (FAN No. 2 relay terminal) - Body ground
    Always
    Below 1 Ω

  1. Reinstall the FAN No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
OK


16.INSPECT COOLING FAN MOTOR
  1. Inspect the cooling fan motor .



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
  1. Disconnect the A45 cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A45-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the A45 cooling fan motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
OK


18.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the A45 cooling fan motor connector.

  1. Remove the FAN No. 1 and FAN No. 2 relays from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A45-2 - 3 (FAN No. 1 relay terminal)
    Always
    Below 1 Ω
    A45-2 - 4 (FAN No. 2 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A45-2 or 3 (FAN No. 1 relay terminal) or 4 (FAN No. 2 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A45 cooling fan motor connector.

  1. Reinstall the FAN No. 1 and FAN No. 2 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
OK


19.INSPECT NO. 2 COOLING FAN MOTOR
  1. Inspect the No. 2 cooling fan motor .



NG
REPLACE NO. 2 COOLING FAN MOTOR (Click here)
OK


20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the A46 No. 2 cooling fan motor connector.

  1. Remove the FAN No. 2 and FAN No. 3 relays from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A46-1 - 3 (FAN No. 2 relay terminal)
    Always
    Below 1 Ω
    A46-2 - 3 (FAN No. 3 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A46-1 or 3 (FAN No. 2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    A46-2 or 3 (FAN No. 3 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A46 No. 2 cooling fan motor connector.

  1. Reinstall the FAN No. 2 and FAN No. 3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
OK


21.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY - FAN NO. 2 RELAY)


    A280297E01
  1. Remove the FAN No. 1 and FAN No. 2 relays from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (FAN No. 1 relay terminal) - 2 (FAN No. 2 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (FAN No. 1 relay terminal) or 2 (FAN No. 2 relay terminal) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    FAN No. 1 Relay Terminals
    *3
    FAN No. 2 Relay Terminals

  1. Reinstall the FAN No. 1 and FAN No. 2 relays.



NG
REPLACE ENGINE ROOM RELAY BLOCK
OK


22.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the A35 ECM connector.

  1. Remove the FAN No. 2 and FAN No. 3 relays from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A35-11 (FAN1) - 1 (FAN No. 1 relay terminal)
    Always
    Below 1 Ω
    A35-11 (FAN1) - 2 (FAN No. 2 relay terminal)
    Always
    Below 1 Ω
    A35-12 (FAN2) - 1 (FAN No. 3 relay terminal)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A35-11 (FAN1) or 1 (FAN No. 1 relay terminal) or 2 (FAN No. 2 relay terminal) - Body ground
    Always
    10 kΩ or higher
    A35-12 (FAN2) or 1 (FAN No. 3 relay terminal) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A35 ECM connector.

  1. Reinstall the FAN No. 2 and FAN No. 3 relays.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
OK

REPLACE ECM (Click here)