Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter detects the fuel sender gauge malfunction.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When combination meter detects fuel sender gauge malfunction
  1. Harness or connector
  2. Combination meter assembly
  3. Fuel sender gauge assembly
  4. No. 2 Fuel sender gauge assembly
  5. Fuel suction tube assembly with pump and gauge
  6. Fuel tank return tube sub-assembly

WIRING DIAGRAM


E246788E02


INSPECTION PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. According to the display on the tester, read the Data List.

    Combination Meter 
    Item
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel sender gauge input
    Min.: 0
    Max.: 127.5
    Fuel sender input value
    Unit: Liter

    OK:
    Fuel input signal displayed on the tester is approximately the same as the fuel receiver gauge indication.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly (Click here).

  1. Inspect the fuel sender gauge assembly (Click here).



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


3.INSPECT FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
E246789E01
  1. Remove the fuel suction tube assembly with pump and gauge (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connector
    Condition
    Specified Condition
    G7-1 (FS+) - 1
    Always
    Below 1 Ω
    G7-2 (FS-) - 2
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Fuel Suction Tube Assembly with Pump and Gauge)


NG
REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE (Click here)
OK


4.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY
  1. Remove the No. 2 fuel sender gauge assembly (Click here).

  1. Inspect the No. 2 fuel sender gauge assembly (Click here).



NG
REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


5.INSPECT FUEL TANK RETURN TUBE SUB-ASSEMBLY
E246790E01
  1. Remove the fuel tank return tube sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connector
    Condition
    Specified Condition
    G6-1 (L) - 3
    Always
    Below 1 Ω
    G6-2 (FS+) - 2
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Fuel Tank Return Tube Sub-assembly)


NG
REPLACE FUEL TANK RETURN TUBE SUB-ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the D7 combination meter assembly connector.

  1. Disconnect the G7 fuel suction tube assembly with pump and gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connector
    Condition
    Specified Condition
    D7-28 (FS-) - G7-2 (FS-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connector
    Condition
    Specified Condition
    D7-28 (FS-) or G7-2 (FS-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE - FUEL TANK RETURN TUBE SUB-ASSEMBLY)
  1. Disconnect the G7 fuel suction tube assembly with pump and gauge connector.

  1. Disconnect the G6 fuel tank return tube sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connector
    Condition
    Specified Condition
    D7-1 (FS+) - G6-2 (FS+)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connector
    Condition
    Specified Condition
    D7-1 (FS+) or G6-2 (FS+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL TANK RETURN TUBE SUB-ASSEMBLY)
  1. Disconnect the D7 combination meter assembly connector.

  1. Disconnect the G6 fuel tank return tube sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connector
    Condition
    Specified Condition
    D7-27 (L) - G6-1 (L)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connector
    Condition
    Specified Condition
    D7-27 (L) or G6-1 (L) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)