Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1678    Lost Communication with Rear Floor Airbag Sensor LH

DTC    B1679    Rear Floor Airbag Sensor LH Initialization Incomplete

for Preparation Click here


DESCRIPTION

  1. The No. 2 airbag sensor assembly circuit consists of the airbag ECU assembly and No. 2 airbag sensor assembly.
  2. The No. 2 airbag sensor assembly detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.
  3. These DTCs are stored when a malfunction is detected in the No. 2 airbag sensor assembly circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1678
B1679
  1. The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the No. 2 airbag sensor assembly circuit.
  2. No. 2 airbag sensor assembly malfunction.
  3. Airbag ECU assembly malfunction.
  1. Floor wire
  2. No. 2 airbag sensor assembly
  3. Airbag ECU assembly

WIRING DIAGRAM


C259335E01


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag ECU assembly and No. 2 airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag ECU assembly and No. 2 airbag sensor assembly.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


Go to step 3

2.CHECK FLOOR WIRE (OPEN)


    C263722E01
  1. Using a service wire, connect terminals 11 (BBL2+) and 12 (BBL2-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H16-1 (BBL2-) - H16-2 (BBL2+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

Text in Illustration 
*1
No. 2 Airbag Sensor Assembly
*2
Airbag ECU Assembly
*3
Floor Wire
*4
Service Wire
*a
Front view of wire harness connector
(to Airbag ECU Assembly)
*b
Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (SHORT)


    C259242E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H16-1 (BBL2-) - H16-2 (BBL2+)
    Always
    1 MΩ or higher

Text in Illustration 
*1
No. 2 Airbag Sensor Assembly
*2
Airbag ECU Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


NG
REPLACE FLOOR WIRE
OK


Go to step 5

4.CHECK FLOOR WIRE (SHORT TO B+)


    C259242E01
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H16-1 (BBL2-) - Body ground
    Ignition switch ON
    Below 1 V
    H16-2 (BBL2+) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Text in Illustration 
*1
No. 2 Airbag Sensor Assembly
*2
Airbag ECU Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


NG
REPLACE FLOOR WIRE
OK


Go to step 6

5.CHECK FLOOR WIRE (SHORT TO GROUND)


    C259242E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H16-1 (BBL2-) - Body ground
    Always
    1 MΩ or higher
    H16-2 (BBL2+) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
No. 2 Airbag Sensor Assembly
*2
Airbag ECU Assembly
*3
Floor Wire
*a
Front view of wire harness connector
(to No. 2 Airbag Sensor Assembly)


NG
REPLACE FLOOR WIRE
OK


6.CHECK NO. 2 AIRBAG SENSOR ASSEMBLY


    C238224E01
  1. Connect the connectors to the No. 2 airbag sensor assembly and airbag ECU assembly.

  1. Replace the No. 2 airbag sensor assembly with a new one.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result
    Proceed to
    DTCs B1678 and B1679 are not output.
    A
    DTC B1678 or B1679 is output.
    B

    HINT:
    Codes other than DTCs B1678 and B1679 may be output at this time, but they are not related to this check.

Text in Illustration 
*1
No. 2 Airbag Sensor Assembly
*2
Airbag ECU Assembly


B
REPLACE AIRBAG ECU ASSEMBLY (Click here)
A

END (NO. 2 AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)