Home › Engine / Hybrid System › FA20 ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL

REAR CRANKSHAFT OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL REAR ENGINE OIL SEAL
  1. Apply engine oil to the lip of a new rear engine oil seal.

    NOTICE:
    Keep the lip free of foreign matter.



    A276049E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07150)

    Oil seal tap in depth:
    0 to 1.0 mm (0 to 0.0394 in.)

    NOTICE:
    1. Wipe any extra grease off of the crankshaft.
    2. Keep the lip free of foreign matter.
    3. Do not tap on the oil seal at an angle.



2. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Clean the 8 bolts and 8 bolt holes.



    A276050E01
  1. Install the No. 1 crankshaft position sensor plate.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Pin

    HINT:
    Align the pin of the front drive spacer with the pin hole of the crankshaft.



3. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


    A276036E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Install the flywheel sub-assembly onto the crankshaft.



    A276046E01
  1. In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }



4. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)


    C258514E01
  1. Insert SST into the clutch disc assembly, and then insert them both into the flywheel sub-assembly.
    Text in Illustration 
    *1
    Clutch Disc Assembly
    *2
    Flywheel Sub-assembly

    SST
    09301-00110  

    NOTICE:
    Insert the clutch disc assembly in the correct direction.



5. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)


  1. Reuse the flywheel sub-assembly and clutch cover assembly:



      C277360E01
    1. Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.
      Text in Illustration 
      *a
      Matchmark



  1. Replace the flywheel sub-assembly or clutch cover assembly:



      C276917E01
    1. Position the clutch cover assembly so that there is a gap of at least 120° between the unbalance marks on the flywheel sub-assembly and the clutch cover assembly.
      Text in Illustration 
      *a
      Unbalance Mark



    C277361E01
  1. Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

    SST
    09301-00110  

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

    HINT:
    1. Following the order in the illustration, tighten the bolts evenly one at a time.
    2. Move SST up, down, right and left lightly after checking that the disc is in the center, and tighten the bolts.



6. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


    A276036E01
  1. Using SST, hold the crankshaft pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Install the drive plate and ring gear sub-assembly and rear drive plate spacer onto the crankshaft.



    A276896E01
  1. In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



7. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)


8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


9. INSPECT FOR OIL LEAK