Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Hazard Warning Switch Circuit

for Preparation Click here


DESCRIPTION

the low beam headlights do not illuminate, or a communication malfunction is detected between the headlight assembly and main body ECU (multiplex network body ECU).

WIRING DIAGRAM


w/ side turn signal light

E351709E01


w/o side turn signal light

E351710E01


INSPECTION PROCEDURE

1.CHECK VEHICLE TYPE
  1. Check vehicle type.


Result:

Result
Proceed to
w/ side turn signal light
A
w/o side turn signal light
B



B
Go to step 8
A


2.READ VALUE USING GTS (HAZARD SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Hazard Switch
    Hazard warning signal switch signal
    ON or OFF
    ON: Hazard switch on
    OFF: Hazard switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Disconnect the D61 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-16 - D61-8 (EHW)
    Always
    Below 1 Ω
    3B-16 or D61-8 (EHW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.



    E351716E01
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-14 - 3B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPAIR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPAIR TURN SIGNAL FLASHER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CLOCK ASSEMBLY (HAZARD WARNING SIGNAL SWITCH) )
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Disconnect the D18 clock assembly (hazard warning signal switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-14 - D18-7
    Always
    Below 1 Ω
    D18-8 - Body ground
    Always
    Below 1 Ω
    D18-14 - Body ground
    Always
    Below 1 Ω
    3B-14 or D18-7 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT CLOCK ASSEMBLY (HAZARD WARNING SIGNAL SWITCH)
  1. Remove the clock assembly (hazard warning signal switch) (Click here).

  1. Inspect the clock assembly (hazard warning signal switch) (Click here).



NG
REPAIR CLOCK ASSEMBLY (HAZARD WARNING SIGNAL SWITCH) (Click here)
OK


7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.



  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


    E249231E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3B-16 - MB-3
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPAIR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPAIR MAIN BODY ECU (NETWORK GATEWAY ECU) 

8.READ VALUE USING GTS (HAZARD SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Hazard Switch
    Hazard warning signal switch signal
    ON or OFF
    ON: Hazard switch on
    OFF: Hazard switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 11
OK


9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Disconnect the D61 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-16 - D61-8 (EHW)
    Always
    Below 1 Ω
    3B-16 or D61-8 (EHW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.



    E351716E01
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-14 - 3B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPAIR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPAIR TURN SIGNAL FLASHER ASSEMBLY (Click here)  

11.CHECK HARNESS AND CONNECTOR
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Disconnect the D18 clock assembly (hazard warning signal switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-14 - D18-7 (HAZRD+)
    Always
    Below 1 Ω
    D18-8 (GND) - Body ground
    Always
    Below 1 Ω
    D18-14 (GND) - Body ground
    Always
    Below 1 Ω
    3B-14 or D18-7 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT CLOCK ASSEMBLY (HAZARD WARNING SIGNAL SWITCH)
  1. Remove the clock assembly (hazard warning signal switch) (Click here).

  1. Inspect the clock assembly (hazard warning signal switch) (Click here).



NG
REPAIR CLOCK ASSEMBLY (HAZARD WARNING SIGNAL SWITCH) (Click here)
OK


13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.



    E351716E01
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-14 - 3B-33
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPAIR INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPAIR MAIN BODY ECU (NETWORK GATEWAY ECU)