Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Turn Signal Switch Circuit

for Preparation Click here


DESCRIPTION

The turn signal flasher assembly receives the main body ECU (network gateway ECU) information and controls the turn signal lights.

WIRING DIAGRAM


w/ Side Turn Signal Light

E351705E01


E351704E01


w/o Side Turn Signal Light

E351707E01


E351708E01


INSPECTION PROCEDURE

1.CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result:

    Result
    Proceed to
    w/ side turn signal light
    A
    w/o side turn signal light
    B



B
Go to step 9
A


2.READ VALUE USING GTS (TURN SIGNAL SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Left Turn Signal Switch
    Left turn signal switch signal
    ON or OFF
    ON: Left turn signal switch on
    OFF: Left turn signal switch off
    -
    Right Turn Signal Switch
    Right turn signal switch signal
    ON or OFF
    ON: Right turn signal switch on
    OFF: Right turn signal switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 7
OK


3.READ VALUE USING GTS (TURN SIGNAL LIGHT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Left Turn Signal Light
    Left turn signal light output
    ON or OFF
    ON: Left turn signal switch on
    OFF: Left turn signal switch off
    -
    Right Turn Signal Light
    Right turn signal light output
    ON or OFF
    ON: Right turn signal switch on
    OFF: Right turn signal switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 4
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) 

4.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the 3B and 3C main body ECU (network gateway ECU) connectors.

  1. Disconnect the D61 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-23 - D61-5
    Always
    Below 1 Ω
    3C-27 - D61-6
    Always
    Below 1 Ω
    3B-23 or D61-5 - Body ground
    Always
    10 kΩ or higher
    3C-27 or D61-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Disconnect the 3A main body ECU (network gateway ECU) connectors.

  1. Disconnect the D61 turn signal flasher assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-4 - D61-2 (LR)
    Always
    Below 1 Ω
    3A-6 - D61-3 (LL)
    Always
    Below 1 Ω
    3A-4 or D61-2 (LR) - Body ground
    Always
    10 kΩ or higher
    3A-6 or D61-3 (LL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Disconnect the 3A, 3C and 3D instrument panel junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-4 - 3C-20
    Always
    Below 1 Ω
    3A-4 - 3C-32
    Always
    Below 1 Ω
    3A-4 - 3D-1
    Always
    Below 1 Ω
    3A-6 - 3C-16
    Always
    Below 1 Ω
    3A-6 - 3C-31
    Always
    Below 1 Ω
    3A-6 - 3D-18
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)  

7.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Inspect the headlight dimmer switch assembly .



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - HEADLIGHT DIMMER SWITCH ASSEMBLY)
  1. Disconnect the D5 and D6 main body ECU (network gateway ECU) connectors.

  1. Disconnect the D50 headlight dimmer switch assembly connectors.

  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D5-17 - D50-15(TL)
      Always
      Below 1 Ω
      D6-9 - D50-13(TR)
      Always
      Below 1 Ω
      D50-12(EL) - Body ground
      Always
      Below 1 Ω
      D5-17 or D50-15(TL) - Body ground
      Always
      10 kΩ or higher
      D6-9 or D50-13(TR) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D5-17 - D50-18(TL)
      Always
      Below 1 Ω
      D6-9 - D50-16(TR)
      Always
      Below 1 Ω
      D50-19(EL) - Body ground
      Always
      Below 1 Ω
      D5-17 or D50-18(TL) - Body ground
      Always
      10 kΩ or higher
      D6-9 or D50-16(TR) - Body ground
      Always
      10 kΩ or higher



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)  

9.READ VALUE USING GTS (TURN SIGNAL SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Left Turn Signal Switch
    Left turn signal switch signal
    ON or OFF
    ON: Left turn signal switch on
    OFF: Left turn signal switch off
    -
    Right Turn Signal Switch
    Right turn signal switch signal
    ON or OFF
    ON: Right turn signal switch on
    OFF: Right turn signal switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 13
OK


10.READ VALUE USING GTS (TURN SIGNAL LIGHT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Left Turn Signal Light
    Left turn signal light output
    ON or OFF
    ON: Left turn signal switch on
    OFF: Left turn signal switch off
    -
    Right Turn Signal Light
    Right turn signal light output
    ON or OFF
    ON: Right turn signal switch on
    OFF: Right turn signal switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 11
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) 

11.INSPECT HEADLIGHT DIMMER SWITCH
  1. Remove the headlight dimmer switch assembly (Click here).

  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - HEADLIGHT DIMMER SWITCH ASSEMBLY)
  1. Disconnect the D61 turn signal flasher assembly connectors.

  1. Disconnect the D50 headlight dimmer switch assembly connectors.

  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D50-15(TL) - D61-5(EL)
      Always
      Below 1 Ω
      D50-13(TR) - D61-6(ER)
      Always
      Below 1 Ω
      D50-12(EL) - Body ground
      Always
      Below 1 Ω
      D50-15(TL) or D61-5(EL) - Body ground
      Always
      10 kΩ or higher
      D50-13(TR) or D61-6(ER) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D50-18(TL) - D61-5(EL)
      Always
      Below 1 Ω
      D50-16(TR) - D61-6(ER)
      Always
      Below 1 Ω
      D50-19(EL) - Body ground
      Always
      Below 1 Ω
      D50-18(TL) or D61-5(EL) - Body ground
      Always
      10 kΩ or higher
      D50-16(TR) or D61-6(ER) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)  

13.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3A instrument panel junction block assembly connectors.

  1. Disconnect the D61 turn signal flasher assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-4 - D61-2 (LR)
    Always
    Below 1 Ω
    3A-6 - D61-3 (LL)
    Always
    Below 1 Ω
    3A-4 or D61-2 (LR) - Body ground
    Always
    10 kΩ or higher
    3A-6 or D61-3 (LL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Disconnect the 3A, 3C and 3D instrument panel junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-4 - 3C-20
    Always
    Below 1 Ω
    3A-4 - 3D-1
    Always
    Below 1 Ω
    3A-6 - 3C-16
    Always
    Below 1 Ω
    3A-4 - 3D-18
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE TURN SIGNAL FLASHER ASSEMBLY (Click here)