Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0461  Fuel Level Sensor "A" Circuit Range / Performance  P0462  Fuel Level Sensor "A" Circuit Low  P0463  Fuel Level Sensor "A" Circuit High  


DESCRIPTION

The signal output from the sender gauge assembly installed in the fuel tank is converted to a CAN communication signal using the combination meter assembly, and this signal is input into the ECM as a remaining fuel signal.

DTC No. DTC Detection Condition Trouble Area
P0461 Compared with the estimated fuel consumption, the actual variation in the fuel sender gauge assembly signal is small.
(2 trip detection logic)
·

Fuel sender gauge assembly

·

Fuel sender gauge assembly No. 2

·

Combination meter assembly

·

ECM


P0462 Fuel sender gauge assembly voltage is less than 0.35 V for 2.5 seconds or more.
(2 trip detection logic)
P0463 Fuel sender gauge assembly voltage is higher than 7.183 V for 1 second or more.
(2 trip detection logic)

MONITOR DESCRIPTION

The ECM uses the fuel sender gauge to monitor the amount of fuel. There are several checks that the ECM performs to confirm the proper operation of the fuel sender gauge.

P0461

If the fuel sender gauge variation is lower than the estimated fuel consumption calculated from the fuel injection quantity and the engine speed, the ECM interprets this as a malfunction in the fuel sender gauge, and stores the DTC.


P0462, P0463

If an open or short in the fuel sender gauge signal line is detected, the ECM interprets this as a malfunction in the fuel sender gauge, and stores the DTC.


CONFIRMATION DRIVING PATTERN

P0461
1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

7.

Drive the vehicle and consume more than 30 liters (31.7 US qts) of the fuel.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0461.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.





P0462, P0463
1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher .

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P462 or P0463.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.





WIRING DIAGRAM

A280187E08
4.969,1.708 5.479,2.01 0.51,0.302 10 false CANH 4.958,0.854 5.458,1.156 0.5,0.302 10 false CANL 5.5,2.531 6,2.74 0.5,0.208 10 false ECM 4.896,2.531 5.167,2.708 0.271,0.177 10 false A33 4.688,1.521 4.938,1.833 0.25,0.313 10 false 19 4.688,0.719 4.938,1.031 0.25,0.313 10 false 18 2.552,0.708 2.802,1.021 0.25,0.313 10 false 7 2.542,1.521 2.792,1.833 0.25,0.313 10 false 6 2.063,1.708 2.552,2.01 0.49,0.302 10 false CANH 2.063,0.875 2.563,1.177 0.5,0.302 10 false CANL 1.302,2.729 2.76,3.281 1.458,0.552 10 false Combination Meter Assembly 1.302,2.552 1.635,2.729 0.333,0.177 10 false D7 0.729,3.292 3.5,3.615 2.771,0.323 10 false : CAN Communication Line

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0461, P0462 or P0463 is output A
DTC P0461, P0462 or P0463 and other DTCs are output B




A

B