Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  U0073  Control Module Communication Bus "A" Off  U0101  Lost Communication with TCM  U0122  Lost Communication with Vehicle Dynamics Control Module  U0155  Lost Communication with Instrument Panel Cluster (IPC) Control Module  U0402  Invalid Data Received from TCM  U0416  Invalid Data Received from Vehicle Dynamics Control Module  U0423  Invalid Data Received from Instrument Panel Cluster Control Module  


DESCRIPTION

Refer to CAN communication system for system description (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DESCRIPTION).

DTC No. DTC Detection Conditions Trouble Areas
U0073 Bus off state for 0.436 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM


U0101 No communication between ECM and TCM for 0.5 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

TCM


U0122 No communication between ECM and skid control ECU for 0.5 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

Brake actuator assembly


U0155 No communication between ECM and combination meter assembly for 0.5 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

Combination meter assembly


U0402 Invalid data received from TCM for 2 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

TCM


U0416 Invalid data received from skid control ECU for 2 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

Brake actuator assembly


U0423 Invalid data received from combination meter assembly for 2 seconds or more
(1 trip detection logic)
·

Wire harness (CANL and CANH circuits)

·

ECM

·

Combination meter assembly



MONITOR DESCRIPTION

The ECM, TCM, skid control ECU and combination meter assembly communicate with each other via the CAN communication line. If there is a problem in this communication, the ECM stores the DTC.

CAUTION / NOTICE / HINT

Go to CAN communication system for troubleshooting (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:
·

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the CAN communication malfunctions, there is no data output from the ECM. In this case, some of the freeze frame data are not correct and not identical with the ECM data, but the ECM data are correct.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC U0073, U0101, U0122, U0155, U0402, U0416 or U0423 is output A
DTC U0073, U0101, U0122, U0155, U0402, U0416 or U0423 and other DTCs are output B




A

B