Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM D

NETWORKING  CAN COMMUNICATION SYSTEM  SYSTEM DESCRIPTION  


BRIEF DESCRIPTION


a.

The Controller Area Network (CAN) is a serial data communication system for real time application. It is a vehicle multiplex communication system which has a high communication speed and the ability to detect malfunctions.

C238999E01
0.209,2.062 1.143,2.208 0.934,0.145 10 CAN Main Bus 1.167,2.131 1.424,2.131 1.424,2.131 1.424,1.772 false 3.435,3.183 4.226,3.329 0.791,0.145 10 CAN Branch 4.249,3.252 4.507,3.252 4.507,3.252 4.745,3.019 false 1.421,3.66 3.257,3.805 1.836,0.145 10 : CAN Main Bus Line (CANH) 1.421,4.094 3.257,4.239 1.836,0.145 10 : CAN Main Bus Line (CANL) 4.825,3.66 6.523,3.805 1.698,0.145 10 : CAN Branch Line (CANH) 4.825,4.094 6.523,4.239 1.698,0.145 10 : CAN Branch Line (CANL) 1.712,2.63 2.090,2.775 0.378,0.145 10 DLC3 3.393,2.63 3.712,2.775 0.319,0.145 10 ECU 5.312,2.63 5.631,2.775 0.319,0.145 10 ECU


b.

Using the CANH and CANL bus lines as a pair, CAN communication is performed using a voltage differential. (A base voltage is applied to the pair of lines and a voltage differential is created when communicating.)


c.

Many ECUs or sensors installed on the vehicle operate by sharing information and communicating with each other.


d.

The CAN has two resistors of 120 Ω which are necessary to enable communication.


e.

Control system CAN is composed of 1 bus.



DEFINITION OF TERMS


a.

Main bus

i.

The main bus is a wire harness between the two terminating resistors on the bus. This is the main bus in the CAN communication system.



b.

Branch

i.

The branch is a wire harness which diverges from the main bus to an ECU or sensor.



c.

Terminating resistors

i.

Two resistors of 120 Ω are installed in parallel across the ends of the CAN main bus lines. They are called terminating resistors. These resistors allow the changes of the voltage differential between the CAN bus lines to be accurately judged. To allow proper function of CAN communication, it is necessary to have both terminating resistors installed. Since the two resistors are installed in parallel, this results in a measurement of approximately 60 Ω.




ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM


a.

V Bus

i.

Main body ECU (network gateway ECU)


ii.

Combination meter assembly


iii.

Certification ECU (smart key ECU assembly)*1


iv.

ECM


v.

TCM*2


vi.

Skid control ECU (brake actuator assembly)


vii.

Steering angle sensor (spiral cable sub-assembly)


viii.

Power steering ECU assembly


ix.

Air conditioning control assembly*3


x.

Air bag ECU assembly

*1 : w/ Entry and Start System

*2 : for Automatic Transmission System

*3 : for Automatic Air Conditioning System




CIRCUIT DESCRIPTION


a.

The V bus has termination circuits with two resistors of 120 Ω.



TROUBLESHOOTING REMARKS


a.

DTCs for the CAN communication system can be checked using the GTS. The DLC3 is connected to the CAN communication system, but no DTCs exist regarding problems in the DLC3 or the DLC3 branch lines. If there is any trouble in the DLC3 or the DLC3 branch lines, ECUs on the CAN cannot output DTCs to the GTS.


b.

Troubles in the CAN V bus (communication lines) can be checked by measuring the resistance between the terminals of the DLC3. However, an open circuit in a branch line other than the DLC3 branch lines cannot be checked from the DLC3 (except branch line of the DLC3).

NOTICE:

Do not insert the tester probes directly into the DLC3. Be sure to use service wires.




DIAGNOSTIC TROUBLE CODES FOR CAN COMMUNICATION SYSTEM


HINT:

See Diagnosis System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HOW TO DISTINGUISH CONNECTOR OF CAN JUNCTION CONNECTOR


a.

In the CAN communication system, the shape of the connectors connected to the CAN junction connector which has an earth terminal is the same. The connectors connected to the CAN junction connector can be distinguished by the colors of the bus lines and the connecting side of the junction connector.

HINT:

See Terminals of ECU for bus line color or the shape of connecting surface (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).