Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › TIMING CHAIN
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297490 TIMING CHAIN A

FA20 ENGINE MECHANICAL  TIMING CHAIN  INSTALLATION  


PROCEDURE

Hide 13506 1.INSTALL CHAIN SUB-ASSEMBLY (for Bank 2)

NOTICE:

Do not allow any foreign matter to adhere onto or to enter into the component parts during installation.


HINT:

Apply engine oil to all component parts of the chain sub-assembly.


a.
A279536E01
0.547,0.123 0.728,0.296 0.180,0.173 10 *2 1.599,0.5 1.779,0.673 0.180,0.173 10 *1 1.328,0.776 1.599,0.644 false 0.752,0.252 0.972,0.369 false

Move the link plate in the direction of the arrow in the illustration to press in the plunger.

Text in Illustration
*1 Link Plate
*2 Plunger


b.
A279537E01
2.059,0.324 2.228,0.490 0.169,0.166 10 *1 3.039,0.276 3.209,0.442 0.169,0.166 10 *2 3.045,0.422 2.879,0.581 false 2.248,0.431 2.791,0.548 false

Insert an approximately 1 mm (0.039 in.) wire or the like into the chain tensioner through the stopper pin hole, and hold the plunger.

HINT:

If the stopper pin hole on the link plate and the stopper pin hole on the chain tensioner are not aligned, check that the first notch of the plunger rack is engaged with the stopper tooth. If not engaged, retract the plunger a little so that the first notch of the plunger rack is engaged with the stopper tooth.


Text in Illustration
*1 First notch of the plunger rack
*2 Stopper Tooth


c.
A334225E03
1.74,0.667 1.5,0.365 true 2.198,1.417 2.25,1.063 true 1.021,0.677 1.292,0.885 0.271,0.208 10 false *b 2.719,1.281 2.979,1.49 0.26,0.208 10 false *b 2.219,0.875 2.417,1.031 0.198,0.156 10 false *a 1.302,0.177 1.5,0.333 0.198,0.156 10 false *a

Position the alignment marks on the camshaft timing intake gear assembly LH and camshaft timing exhaust gear assembly LH as shown in the illustration.

NOTICE:

To avoid damaging the valves, do not turn the camshaft timing intake gear assemblies more than the zero-lift range (the range where camshaft timing intake gear assembles can be turned lightly by hand).


Text in Illustration
*a Alignment Mark
*b 25° to 30°


d.
A334222E01
0.455,1.767 0.655,1.939 0.200,0.173 10 *a 0.787,1.47 0.579,1.744 false

Check that the alignment mark on the crankshaft timing gear or sprocket is at the position shown in the illustration.

Text in Illustration
*a Crankshaft Timing Gear Key


e.
A279541E02
3.087,1.063 3.273,1.230 0.186,0.167 10 *d 1.891,2.968 2.077,3.135 0.186,0.167 10 *d 1.333,0.093 1.519,0.260 0.186,0.167 10 *c 2.72,1.063 2.906,1.230 0.186,0.167 10 *b 2.993,2.019 3.179,2.186 0.186,0.167 10 *b 1.32,0.583 1.506,0.750 0.186,0.167 10 *a 0.385,0.314 1.318,0.218 false 0.367,0.406 1.313,0.692 false 2.92,0.64 2.835,1.063 false 3.018,0.647 3.172,1.06 false 2.774,2.812 3.039,2.195 false 2.755,2.915 2.088,3.057 false

Install the chain sub-assembly in the following order.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

Align the mark plate (grayish blue) on the chain sub-assembly with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly LH.


iii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing intake gear assembly LH.



f.

Apply engine oil to the bolt.


g.

Using a 5 mm hexagon socket wrench, install the No. 1 chain vibration damper with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


h.
A279532

Install a new O-ring to the cylinder block (bank 2).


i.
A279531

Install the chain tensioner slipper.


j.

Install the No. 2 chain tensioner assembly with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


k.
A279542E01
3.086,1.037 3.272,1.204 0.186,0.167 10 *d 1.836,2.915 2.021,3.083 0.186,0.167 10 *d 1.332,0.114 1.518,0.281 0.186,0.167 10 *c 2.719,1.037 2.905,1.204 0.186,0.167 10 *b 2.948,1.905 3.134,2.072 0.186,0.167 10 *b 1.319,0.604 1.505,0.771 0.186,0.167 10 *a 0.384,0.335 1.317,0.239 false 0.367,0.427 1.312,0.712 false 2.919,0.614 2.834,1.037 false 3.017,0.621 3.171,1.033 false 2.719,2.759 3.003,2.101 false 2.699,2.862 2.032,3.005 false

Check that the chain is correctly installed.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

The mark plate (grayish blue) on the chain sub-assembly is aligned with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing intake gear assembly LH.


iii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly LH.



l.

Pull out the wire or the like from the No. 2 chain tensioner assembly.


m.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


n.

Using SST, turn the crankshaft clockwise to make sure that there are no abnormal conditions.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Be sure to perform this confirmation.



Hide 13506 2.INSTALL CHAIN SUB-ASSEMBLY (for Bank 1)

NOTICE:

Do not allow any foreign matter to adhere onto or to enter into the component parts during installation.


HINT:

Apply engine oil to all component parts of the chain sub-assembly.


a.
A279544E01
0.214,1.078 0.384,1.246 0.170,0.168 10 *1 1.749,0.661 1.919,0.829 0.170,0.168 10 *2 1.099,1.032 0.404,1.154 false 1.383,0.662 1.737,0.76 false

Move the link plate in the direction of the arrow in the illustration to press in the plunger.

Text in Illustration
*1 Link Plate
*2 Plunger


b.
A279545E03
2.188,0.458 2,0.302 false 2.292,0.479 2.521,0.667 false 1.823,0.188 2.104,0.385 0.281,0.198 10 false *2 2.49,0.698 2.667,0.854 0.177,0.156 10 false *1

Insert a 2.5 mm (0.098 in.) hexagon wrench into the No. 1 chain tensioner assembly through the stopper pin hole, and hold the plunger.

Text in Illustration
*1 First notch of the plunger rack
*2 Stopper Tooth

HINT:

If the stopper pin hole on the link plate and the stopper pin hole on the chain tensioner are not aligned, check that the first notch of the plunger rack is engaged with the stopper tooth. If not engaged, retract the plunger a little so that the first notch of the plunger rack is engaged with the stopper tooth.



c.
A334221E03
3.24,0.177 3.01,0.802 true 3.271,1.875 3,1.104 true 2.156,2.573 1.594,2.75 true 1.458,2.677 0.615,3.063 false 0.875,1 0.656,2.344 true 0.406,1.219 0.25,2.167 true 0.104,2.208 0.49,2.396 0.385,0.188 10 false SST 2.177,2.458 2.375,2.646 0.198,0.188 10 false *a 0.542,2.375 0.74,2.563 0.198,0.188 10 false *b 0.438,2.979 0.635,3.167 0.198,0.188 10 false *c 3.208,1.885 3.406,2.073 0.198,0.188 10 false *a 3.208,0.01 3.406,0.198 0.198,0.188 10 false *a 1.771,3.031 2.052,3.208 0.281,0.177 10 false 10°

Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly LH and the camshaft timing exhaust gear assembly LH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

Text in Illustration
*a Alignment Mark
*b Crankshaft Pulley Pin Hole
*c Crankshaft Timing Gear Key

HINT:

At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.



d.

Remove the crankshaft pulley and crankshaft pulley spacer.


e.
A279547E01
0.592,0.976 0.759,1.145 0.167,0.169 10 *a 1.343,0.879 0.795,1.057 0.795,1.057 1.339,1.208 false

Align the alignment marks of the camshaft timing intake gear assembly RH and camshaft timing exhaust gear assembly RH as shown in the illustration.

NOTICE:

To avoid damaging the valves, do not turn the camshaft timing intake gear assembly RH and camshaft more than the zero-lift range (the range where the camshaft timing intake gear assembles can be turned lightly by hand).


Text in Illustration
*a Alignment Mark


f.
A279548E01
1.298,0.238 1.479,0.405 0.181,0.167 10 *d 0.319,1.092 0.500,1.260 0.181,0.167 10 *b 0.153,1.93 0.334,2.097 0.181,0.167 10 *d 1.328,2.949 1.509,3.116 0.181,0.167 10 *c 0.63,1.934 0.811,2.101 0.181,0.167 10 *b 1.32,2.579 1.501,2.747 0.181,0.167 10 *a 0.827,0.464 1.306,0.369 false 0.768,0.575 0.457,1.089 false 0.456,2.693 0.685,2.117 false 0.382,2.642 0.241,2.106 false 2.109,2.926 1.527,2.689 false 2.06,3.016 1.531,3.05 false

Install the chain sub-assembly in the following order.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

Align the mark plate (grayish blue) on the chain sub-assembly with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing intake gear assembly RH.


iii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly RH.



g.

Apply engine oil to the bolt.


h.

Using a 5 mm hexagon socket wrench, install the No. 1 chain vibration damper with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


i.
A279527

Install the chain tensioner slipper.


j.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


k.
A279549E01
1.34,0.19 1.509,0.353 0.169,0.163 10 *d 1.344,0.658 1.514,0.822 0.169,0.163 10 *b 0.174,2.091 0.344,2.254 0.169,0.163 10 *d 1.907,0.68 2.076,0.843 0.169,0.163 10 *c 0.611,2.088 0.780,2.251 0.169,0.163 10 *b 1.907,0.19 2.076,0.353 0.169,0.163 10 *a 0.82,0.475 1.325,0.313 false 0.764,0.595 1.333,0.768 false 2.68,0.749 2.106,0.305 false 2.607,0.82 2.096,0.785 false 0.247,2.267 0.404,2.743 false 0.491,2.781 0.661,2.265 false

Check that the chain is correctly installed.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

The mark plate (grayish blue) on the chain sub-assembly is aligned with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing intake gear assembly RH.


iii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly RH.



l.

Pull out the hexagon wrench from the No. 1 chain tensioner assembly.


m.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


n.

Using SST, turn the crankshaft clockwise to make sure that there are no abnormal conditions.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Be sure to perform this confirmation.



o.

Remove the crankshaft pulley and crankshaft pulley spacer.


Hide 11302 3.INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY