Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297493 FRONT CRANKSHAFT OIL SEAL A

FA20 ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11302A 1.INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

a.

Degrease the area in which to press-fit the oil seal for the timing chain or belt cover sub-assembly.


b.
A375976E01
1.187,1.371 1.139,1.828 false 0.947,1.859 1.293,2.049 0.346,0.190 10 SST 1.644,2.06 1.990,2.249 0.346,0.190 10 SST 2.067,2.71 1.837,2.281 1.837,2.281 1.798,2.705 false 2.796,2.122 3.141,2.311 0.346,0.190 10 SST 2.515,2.528 2.753,2.218 2.753,2.218 2.347,2.445 false

Using SST and a hammer, tap in a new timing chain or belt cover oil seal until its surface is flush with the timing chain or belt cover sub-assembly edge.

SST
09950-60010  (09952-06010, 09951-00490, 09951-00650)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the oil seal at an angle.

·

Do not deform the oil seal.

·

Keep the lip free from foreign matter.

·

Do not apply engine oil to the dust seal section.

·

Do not apply engine oil, etc., to the oil seal or the timing chain or belt cover sub-assembly, because doing so could cause an engine oil leak.



HINT:

Alternatively, the tapping depth of the timing chain or belt cover oil seal can be -1.0 to 0 mm (-0.039 to 0 in.) from the timing chain cover end surface.



Hide 13471 2.INSTALL CRANKSHAFT PULLEY

a.

Install the crankshaft pulley spacer.


b.

Install a new O-ring to the crankshaft pulley spacer.


c.
A302559E01
2.489,1.018 2.872,0.343 false 2.896,0.175 3.089,0.351 0.193,0.177 10 *2 0.824,1.037 1.227,0.343 false 1.252,0.175 1.445,0.351 0.193,0.177 10 *1

Install the crankshaft pulley while aligning the knock hole of the pulley with the knock pin on the crankshaft pulley spacer.

Text in Illustration
*1 Knock Hole
*2 Knock Pin


d.
A302562E01
1.99,3.099 2.698,3.014 false 2.721,2.906 2.913,3.083 0.192,0.177 10 *1 0.91,4.128 1.724,3.822 false 0.712,4.046 0.904,4.223 0.192,0.177 10 *1 1.092,2.128 1.184,1.837 false 0.913,2.14 1.262,2.316 0.350,0.177 10 SST 0.744,3.832 1.015,3.878 false 0.393,3.741 0.743,3.917 0.350,0.177 10 SST

Install SST to the crankshaft pulley.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

HINT:

Position the projections on SST in the direction as shown in the illustration to prevent SST from separating from the crankshaft pulley.


Text in Illustration
*1 Claw


e.

Apply engine oil to the crankshaft pulley set bolt.


f.
A302563E03
1.208,1.49 1.115,1.781 false 1.542,1.906 1.74,2.094 0.198,0.188 10 false *a 3.021,1.198 3.208,1.406 0.188,0.208 10 false *b 0.958,1.813 1.271,2 0.313,0.188 10 false SST

Using SST, hold the crankshaft pulley and tighten the crankshaft pulley set bolt.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*a Hold
*b Turn


g.
A281493E03
1.542,0.948 0.573,1.688 false 2.125,0.99 2.542,1.813 false 2.5,1.875 2.677,2.052 0.177,0.177 10 false *b 0.365,1.656 0.542,1.833 0.177,0.177 10 false *a

Using a marker, draw the reference line (A) on the crankshaft pulley set bolt and also the reference line (B) on the crankshaft pulley according to the line engraved around the crankshaft pulley set bolt head as shown in the illustration.

Text in Illustration
*a Reference Line A
*b Reference Line B

HINT:

There are carved lines on the crankshaft pulley set bolt head every 90°.



h.
A302564E03
0.938,4.031 1.104,3.74 true 2.823,1.427 2.073,1.104 true 2.573,1.708 1.969,1.146 true 1.406,4.198 1.719,4.396 0.313,0.198 10 false *a 2.917,3.302 3.229,3.5 0.313,0.198 10 false *b 2.635,1.708 2.948,1.906 0.313,0.198 10 false *c 2.865,1.365 3.177,1.563 0.313,0.198 10 false *d 0.781,4.073 1.135,4.281 0.354,0.208 10 false SST

Using SST, hold the crankshaft pulley, and tighten the crankshaft pulley set bolt by 90° until the reference lines A and B are aligned.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

Text in Illustration
*a Hold
*b Turn
*c Reference Line A
*d Reference Line B


Hide 16361A 3.INSTALL FAN AND GENERATOR V BELT