Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR(for Direct Injection)
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297501 FUEL INJECTOR(for Direct Injection) A

FA20 FUEL  FUEL INJECTOR(for Direct Injection)  REMOVAL  


PROCEDURE

Hide 23815 2.REMOVE NO. 2 FUEL DELIVERY PIPE

a.
A279756

Using a union nut wrench, loosen the 2 union nuts and remove the No. 2 fuel delivery pipe.

NOTICE:

When removing the No. 2 fuel delivery pipe, pull it out in a straight line to avoid damaging the O-ring seal surface of the fuel delivery pipe LH.



Hide 23814B 3.REMOVE FUEL DELIVERY PIPE

a.
A279757

Remove the 3 bolts.


b.

Using a union nut wrench, loosen the 2 union nuts and remove the fuel delivery pipe.


Hide 23815E 4.REMOVE FUEL DELIVERY PIPE LH

a.
A279758

Disconnect the 2 fuel injector assembly connectors.


b.
A279759

Remove the 2 bolts and fuel delivery pipe LH.


Hide 23814E 5.REMOVE FUEL DELIVERY PIPE RH

a.
A279760

Disconnect the fuel pressure sensor connector and 2 fuel injector assembly connectors.


b.
A279761

Remove the 2 bolts and fuel delivery pipe RH.


Hide 23250 6.REMOVE FUEL INJECTOR ASSEMBLY

a.
A279762E01
0.236,0.101 0.473,0.368 0.238,0.267 10 *a 0.236,2.163 0.473,2.430 0.238,0.267 10 *b

A285177

Remove the 4 fuel injector assemblies from the fuel delivery pipe.

Text in Illustration
*a for Bank 2
*b for Bank 1

NOTICE:
·

If the tip of the fuel injector assembly is struck or the fuel injector assembly is dropped, replace the fuel injector assembly with a new one.

·

Pull and remove the fuel injector assembly in a straight line to avoid damaging the O-ring seal surface of the fuel delivery pipe.

·

For re-installation, attach a tag or label to each fuel injector assembly.



NOTICE:
·

Pull and remove the injector in a straight line to avoid damaging to the seal surface of the delivery pipe O-rings.

·

For reinstallation, attach a tag or label to the injector shaft.




b.
A279763

Remove the No. 1 injector holders from the fuel injectors.


c.
A279765E01
1.979,0.875 2.76,0.594 true 1.948,1.021 2.771,1.208 true 2.833,0.5 3.125,0.771 0.292,0.271 10 *1 2.833,1.167 3.156,1.448 0.323,0.281 10 *2

Using a screwdriver, remove the No. 3 fuel injector back-up ring and fuel injector insulator.

Text in Illustration
*1 No. 3 Fuel Injector Back-up Ring
*2 Fuel Injector Insulator


d.
A279766E02
2.073,0.573 2.396,0.365 true 2.083,0.75 2.406,0.958 true 2.094,0.656 2.417,0.656 true 2.417,0.25 2.604,0.427 0.188,0.177 10 false *1 2.458,0.573 2.646,0.75 0.188,0.177 10 false *2 2.469,0.885 2.656,1.063 0.188,0.177 10 false *3

Using a needle nose plier, remove the No. 2 fuel injector backup ring.

Text in Illustration
*1 No. 2 Fuel Injector Backup Ring
*2 Fuel Injector Seal
*3 No. 1 Fuel Injector Backup Ring


e.

Remove the fuel injector seal and No. 1 fuel injector backup ring.


Hide 23250B 7.REMOVE FUEL INJECTOR O-RING

a.
A279764

Using the tips of a pair of needle nose pliers, pinch and pull one of the fuel injector O-ring at several points to stretch it. Repeat this for the other fuel injector O-ring.

NOTICE:
·

Excessively pinching the fuel injector O-ring may damage the groove of the injector.

·

If an injector is dropped or the tip of the injector is struck, replace it with a new one.




b.

Remove the fuel injector O-ring from the injector.