Home › Engine / Hybrid System › FA20 INTAKE / EXHAUST › EXHAUST PIPE
RM2090E _51 Engine / Hybrid System _060669 FA20 INTAKE / EXHAUST _0297518 EXHAUST PIPE A

FA20 INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17401 1.INSTALL FRONT EXHAUST PIPE SUB-ASSEMBLY

a.

Rope up the front exhaust pipe sub-assembly to the front suspension crossmember.

HINT:

This operation is necessary in order to prevent the front exhaust pipe sub-assembly from falling off.




Hide 17448 2.INSTALL TAIL PIPE BAFFLE (w/ Rear Spoiler)

a.

with knee airbag:

i.
A280286E02
1.885,0.979 1.604,0.396 true 2.042,0.969 1.75,1.615 true 2.104,2.469 2.063,2.031 true 1.479,0.219 1.667,0.385 0.188,0.167 10 false *a 1.635,1.656 1.823,1.823 0.188,0.167 10 false *b 1.969,1.844 2.156,2.01 0.188,0.167 10 false *c

Align the cutout section of the tail pipe baffle with the protrusion of the exhaust pipe assembly tail as shown in the illustration.

Text in Illustration
*a Cutout Section
*b Protrusion
*c Stopper


ii.

Press in the tail pipe baffle until its stopper contacts that of the tail exhaust pipe assembly.


iii.

Install the 2 bolts and the 2 tail pipe baffles.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



b.

without knee airbag:

i.
A282937E02
1.792,1.396 1.49,1.927 true 2.115,1.594 1.979,1.875 true 2.51,1.615 2.792,1.802 true 2.865,1.75 3.021,1.927 0.156,0.177 10 false *3 1.396,1.938 1.552,2.115 0.156,0.177 10 false *1 1.896,1.917 2.052,2.094 0.156,0.177 10 true *2

Press in the tail pipe baffle until the tail exhaust pipe assembly plate contact shown in the illustration.

Text in Illustration
*1 Tail Exhaust Pipe Assembly
*2 Tail Pipe Baffle
*3 Plate
V100145

Contact area


ii.

Install the 2 bolts and the 2 tail pipe baffles.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install the 4 cushion rubbers and the tail exhaust pipe assembly.


Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install the center exhaust pipe assembly with the cushion rubber.


b.

Install the 2 new gaskets and the center exhaust pipe assembly with the 2 new nuts and the 2 bolts.

Torque:
48 N*m (490 kgf*cm, 35 ft.*lbf)

NOTICE:
·

Do not reuse the gaskets.

·

Do not reuse the nuts.




Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Temporarily install the front exhaust pipe assembly to the bracket with the bolt.


b.

Install the new gaskets and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Do not reuse the gaskets.

·

Do not reuse the nuts.




c.

Install the new gaskets and the front exhaust pipe assembly to the front exhaust pipe sub-assembly with the 2 new nuts.

Torque:
43 N*m (439 kgf*cm, 32 ft.*lbf)

NOTICE:
·

Do not reuse the gaskets.

·

Do not reuse the nuts.




d.

Fully tighten the bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 6.INSPECT FOR EXHAUST GAS LEAK

a.

If gas is leaking, tighten the areas necessary to stop the leak. Replace the damaged parts as necessary.


Hide 51442E 7.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the 7 bolts and the No. 2 engine under cover.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 8.INSTALL NO. 1 ENGINE UNDER COVER

a.
A280546

Install the No. 1 engine under cover with the 12 bolts and engage the 7 clips.

V100135

Bolt A
V100136

Bolt B

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 7.5 N*m (76 kgf*cm, 66 in.*lbf)