Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM J

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Pattern Select Switch Circuit  


DESCRIPTION

A signal from the pattern select switch assembly input into the TCM enables switching of the mode.

WIRING DIAGRAM

C259541E02
1.865,2.531 3.354,2.781 1.49,0.25 10 false Pattern Select Switch 4.344,1.677 5.031,1.906 0.688,0.229 10 false 24 4.813,3.021 5.135,3.219 0.323,0.198 10 false TCM 4.344,1.094 5.042,1.302 0.698,0.208 10 false 13 3.281,1.677 3.552,1.875 0.271,0.198 10 false 6 3.271,1.094 3.542,1.292 0.271,0.198 10 false 4 4.823,2.875 5.125,3.083 0.302,0.208 10 false A19 1.708,1.656 2.229,2.177 0.521,0.521 10 false 8 1.875,2.375 2.656,2.573 0.781,0.198 10 false D35 4.583,1.219 5.771,1.531 1.188,0.313 10 false SPORT 4.594,1.802 5.552,2.104 0.958,0.302 10 false SNOW 2.719,1.104 3.292,1.281 0.573,0.177 10 false SPORT 2.75,1.698 3.24,1.865 0.49,0.167 10 false SNOW

HINT:

(*) Pattern Select Switch (ECT SNOW Switch)

When the ECT SNOW switch is pushed, the switch contact is made and the ECT SNOW mode is selected.

To cancel the ECT SNOW mode, push the ECT SNOW switch once again.

The ECT SNOW mode is automatically cancelled out when the ignition switch is turned "off".


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

OK
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sport Switch Status Pattern switch (ECT SPORT) status/
ON or OFF
Ignition switch is:
ON: off
↓
Pattern switch (ECT SPORT) is:
Pushed: ON
↓
Pattern switch (ECT SPORT) is:
Pushed: OFF
-



OK

2.READ VALUE USING GTS

NG

3.INSPECT PATTERN SELECT SWITCH ASSEMBLY
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

OK
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Snow Switch Status Pattern switch (ECT SNOW) status/
ON or OFF
Ignition switch is:
ON: off
↓
Pattern switch (ECT SNOW) is:
Pushed: ON
↓
Pattern switch (ECT SNOW) is:
Pushed: OFF
-



OK

NG

6.INSPECT PATTERN SELECT SWITCH ASSEMBLY
3.INSPECT PATTERN SELECT SWITCH ASSEMBLY
a.

Perform inspection of the pattern select switch (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PATTERN SELECT SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - TCM - BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY - TCM - BODY GROUND)
a.

Disconnect the TCM connector.


b.

Disconnect the pattern select switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
A19-13(SPORT) - D35-4(SPORT) Always Below 1 Ω
D35-8 - Body ground Always Below 1 Ω
A19-3(SPORT) - Body ground Always 10 kΩ or higher



d.

Connect the TCM connector.


e.

Connect the pattern select switch assembly connector.



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PATTERN SELECT SWITCH ASSEMBLY
a.

Perform inspection of the pattern select switch (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PATTERN SELECT SWITCH>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH - TCM - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH - TCM - BODY GROUND)
a.

Disconnect the TCM connector.


b.

Disconnect the pattern select switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
A19-24(SNOW) - D35-6 Always Below 1 Ω
D35-8 - Body ground Always Below 1 Ω
A19-24(SNOW) - Body ground Always 10 kΩ or higher



d.

Connect the TCM connector.


e.

Connect the pattern select switch assembly connector.



OK

8.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR