Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2012.03–2016.06
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM J

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Shift Paddle Switch Circuit  


DESCRIPTION

When the shift lever is in M, it is possible to change into any gear using the steering assembly transmission shift switch.

Additionally, when the vehicle is being driving with the shift lever in D, operating the steering assembly transmission shift switch changes to selection of gears with the shift lever in D, enabling shifting to any gear.

WIRING DIAGRAM

C259540E06
1.698,4.135 3.677,4.344 1.979,0.208 10 false To Transmission Control Switch 2.927,3.021 3.76,3.188 0.833,0.167 10 false Spiral Cable 5.927,3.229 6.281,3.427 0.354,0.198 10 false TCM 5.948,3.063 6.229,3.25 0.281,0.188 10 false A19 1.083,1.115 1.49,1.448 0.406,0.333 10 false + 1.094,1.656 1.281,1.875 0.188,0.219 10 false - 3.99,0.99 4.292,1.156 0.302,0.167 10 false D51 2.385,0.813 2.792,1.146 0.406,0.333 10 false 4 2.396,1.406 2.917,1.896 0.521,0.49 10 false 3 4.052,0.823 4.458,1.156 0.406,0.333 10 false 2 3.979,1.563 4.292,1.75 0.313,0.188 10 false D51 4.052,1.406 4.573,1.656 0.521,0.25 10 false 1 3.979,2.573 4.313,2.74 0.333,0.167 10 false D51 5.448,0.885 6.24,1.208 0.792,0.323 10 false 1 5.469,1.458 5.99,1.948 0.521,0.49 10 false 2 0.781,3.146 1.906,3.375 1.125,0.229 10 false Steering Pad SW 2.406,2.417 2.563,2.594 0.156,0.177 10 false 1 4.052,2.396 4.25,2.594 0.198,0.198 10 false 7 2.365,0.99 2.667,1.167 0.302,0.177 10 false z4 2.375,1.563 2.677,1.74 0.302,0.177 10 false z4 2.375,2.583 2.677,2.76 0.302,0.177 10 false z4 5.698,0.979 6.25,1.25 0.552,0.271 10 false SFTD 5.677,1.563 6.542,1.833 0.865,0.271 10 false SFTU 3.563,1 4.208,1.365 0.646,0.365 10 false SDN 3.583,1.573 4.583,1.781 1,0.208 10 false SUP 0.771,1.906 1.948,2.281 1.177,0.375 10 false Transmission Shift Switch 0.792,2.698 1.615,2.875 0.823,0.177 10 false Switch Wire

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

OK
Tester Display Condition Standard
Sport Shift Up SW Continuously shift to "+" (upshift): ON
Release "+" (up-shift): OFF
-
Sport Shift Down SW Continuously shift to "-" (down-shift): ON
Release "-" (down-shift): OFF
-



OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH - TCM)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A19-1(SFTD) - Body ground Pull continuously
"+"
(Up shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher
A19-2(SFTU) - Body ground Pull continuously
"-"
(Down shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher



c.

Connect the TCM connector.



OK

3.REPLACE TCM

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)
a.

Disconnect the spiral cable connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D51-7 - Body ground Always Below 1 Ω



c.

Connect the spiral cable connector.



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the spiral cable connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A19-1(SFTD) - D51-2 Always Below 1 Ω
A19-2(SFTU) - D51-1 Always Below 1 Ω
A19-1(SFTD) or D51-2 - Body ground Always 10 kΩ or higher
A19-2(SFTU) or D51-1 - Body ground Always 10 kΩ or higher



d.

Connect the TCM connector.


e.

Connect the spiral cable connector.



OK

6.CHECK TRANSMISSION SHIFT SWITCH (TRANSMISSION SHIFT SWITCH - SPIRAL CABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TRANSMISSION SHIFT SWITCH (TRANSMISSION SHIFT SWITCH - SPIRAL CABLE)
a.

Disconnect the spiral cable connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z4-4 - z4-1 Pull continuously
"+"
(Up shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher
z4-3 - z4-1 Pull continuously
"-"
(Down shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher



c.

Connect the spiral cable connector.



OK

NG

7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY
7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY
a.

Inspect the transmission shift switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>INSPECTION).



OK

NG

REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY