Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM2090E _52 Drivetrain _060675 CLUTCH _0297565 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C258514E01
1.444,2.43 1.599,2.583 0.155,0.153 10 *1 2.62,2.427 2.774,2.580 0.155,0.153 10 *2 0.806,2.693 1.102,2.852 0.296,0.159 10 SST 2.896,1.504 3.192,1.664 0.296,0.159 10 SST 2.54,1.582 2.866,1.582 false 2.231,2.425 2.602,2.519 false 1.935,2.514 1.626,2.514 false 1.471,3.138 1.175,2.79 false

Insert SST into the clutch disc assembly, and then insert them both into the flywheel sub-assembly.

Text in Illustration
*1 Clutch Disc Assembly
*2 Flywheel Sub-assembly

SST
09301-00110  

NOTICE:

Insert the clutch disc assembly in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.

Reuse the flywheel sub-assembly and clutch cover assembly:

i.
C277360E01
0.61,0.723 0.788,0.888 0.178,0.165 10 *a 1.09,1.112 0.802,0.826 0.802,0.826 0.998,1.12 false

Align the matchmark on the clutch cover assembly with that on the flywheel sub-assembly.

Text in Illustration
*a Matchmark



b.

Replace the flywheel sub-assembly or clutch cover assembly:

i.
C276917E01
2.531,0.983 2.891,0.983 false 0.995,1.706 1.32,1.382 false 0.831,1.69 0.990,1.840 0.159,0.149 10 *a 2.902,0.902 3.061,1.052 0.159,0.149 10 *a

Position the clutch cover assembly so that there is a gap of at least 120° between the unbalance marks on the flywheel sub-assembly and the clutch cover assembly.

Text in Illustration
*a Unbalance Mark



c.
C277361E01
2.23,0 2.340,0.159 0.110,0.159 10 1 1.126,1.918 1.236,2.077 0.110,0.159 10 2 0.858,0.133 0.968,0.292 0.110,0.159 10 3 2.438,1.795 2.548,1.954 0.110,0.159 10 4 0.55,1.137 0.659,1.296 0.110,0.159 10 5 2.803,0.828 2.913,0.987 0.110,0.159 10 6

Following the procedures shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00110  

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up, down, right and left lightly after checking that the disc is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C258515

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum non-alignment:

0.5 mm (0.0197 in.)



b.
C258516E01
2.093,1.267 2.353,0.869 false 2.378,0.773 2.703,0.942 0.325,0.169 10 SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission assembly.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 31126 5.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the clutch release fork boot to the manual transmission assembly.


Hide 31232A 6.INSTALL RELEASE BEARING HUB CLIP

a.

Install the 3 release bearing hub clips to the clutch release bearing assembly.


b.

Install the release bearing hub clip to the clutch release fork sub-assembly.


Hide 31204 7.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C262086

Apply release hub grease to the contact surfaces of the clutch release fork sub-assembly and clutch release bearing assembly, clutch release fork sub-assembly and clutch release cylinder push rod (Fill concave parts), and clutch release fork sub-assembly and release fork support (Fill concave parts).

Text in Illustration
V100135

Release Hub Grease

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.
C334351

Apply release hub grease to the clutch release bearing assembly as shown in the illustration.

Text in Illustration
V100144

Release Hub Grease

Grease:

Toyota Genuine Release Hub Grease or equivalent



c.

Engage the 2 release bearing hub clips and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31230 8.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transmission assembly.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



b.
U147093E03
1.656,0.979 1.896,0.833 false 1.781,0.938 1.896,1.104 0.115,0.167 10 true A

Apply clutch spline grease to the input shaft spline.

Text in Illustration
V100135

Clutch Spline Grease

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


NOTICE:

Do not apply grease to portion A shown in the illustration.