Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER
RM2090E _53 Suspension _060681 REAR SUSPENSION _0297605 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH and LH sides.



PROCEDURE

Hide 1.INSTALL REAR SHOCK ABSORBER WITH COIL SPRING

a.

Mount the rear shock absorber with coil spring on the vehicle.


b.

Install rear shock absorber with coil spring with the 2 new nuts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 48740F 2.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Replace the mounting nuts of the rear No. 2 suspension arm assembly LH and rear suspension member sub-assembly with new nut and then temporarily tighten them.


b.

Temporarily install the rear No. 2 suspension arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and new nut.

NOTICE:

Insert the bolt from the front of the vehicle.



c.

Temporarily install the rear shock absorber with coil spring with the bolt and new nut.

HINT:

The bolt may be inserted from either direction.



Hide 48802 3.TEMPORARILY INSTALL STABILIZER LINK SUB-ASSEMBLY (for LH Side)

a.

Temporarily install the rear stabilizer link sub-assembly to the rear No. 2 suspension arm assembly LH with the bolt and new nut.


Hide 4.STABILIZE SUSPENSION

a.
C261010E02
1.885,1.802 1.406,1.802 false 1.938,1.708 2.083,1.854 0.146,0.146 10 false *a

Jack up the axle carrier, with a wooden block placed between the jack and axle carrier, to apply load to the suspension so that the rear drive shaft assembly becomes level.

Text in Illustration
*a Wooden Block


Hide 48740F 5.FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Fully tighten the nut on the rear axle carrier sub-assembly LH side.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


b.

Fully tighten the nut holding the rear shock absorber.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


c.

Fully tighten the nut on the rear suspension member sub-assembly side.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 48802 6.FULLY TIGHTEN STABILIZER LINK SUB-ASSEMBLY

a.

Fully tighten the nut rear stabilizer link sub-assembly side.

Torque:
38 N*m (388 kgf*cm, 28 ft.*lbf)


Hide 89408C 7.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ HID Headlight System)

a.

Install the rear height control sensor sub-assembly LH to the rear No. 2 suspension arm assembly LH with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 8.INSTALL REAR WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

Hide 64715D 9.INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

Hide 64711 11.INSTALL LUGGAGE COMPARTMENT FLOOR MAT

Hide 12.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 14. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ HID Headlight System)

Hide 15.ADJUST HEADLIGHT AIMING (w/ HID Headlight System)