Home › Suspension › REAR SUSPENSION › TOE CONTROL LINK
RM2090E _53 Suspension _060681 REAR SUSPENSION _0297608 TOE CONTROL LINK A

REAR SUSPENSION  TOE CONTROL LINK  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Use the same procedure for the RH and LH sides.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 48720A 2.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48706B 3.REMOVE TOE CONTROL LINK SUB-ASSEMBLY LH

a.

Remove the snap pin.


b.
C257521

Remove the nut on the rear axle carrier side.


c.

Install SST (2 pieces of spacer B) to the threaded section of the t toe control link sub-assembly LH.

SST
09960-20010  (09961-02060, 09961-02010)


d.

Using SST (ball join puller), separate the toe control link sub-assembly LH from the rear axle carrier LH.

C256619E05
5.188,0.948 5.469,1.531 false 5.469,1.323 5.292,0.948 5.292,0.948 5.094,0.948 false 6,2.365 6.24,2.365 6.24,2.365 6.24,1.917 false 2.625,0.938 2.115,0.49 2.115,0.49 1.844,0.49 false 1.24,2.25 1.031,2.25 false 5.667,2.125 5.896,2.125 5.896,2.125 5.896,1.948 false 6.677,1.021 6.438,1.021 6.438,1.021 6.438,1.198 false 1.521,0.427 1.813,0.573 0.292,0.146 10 false SST 1.281,2.167 1.427,2.313 0.146,0.146 10 false *b 5.5,2.052 5.646,2.198 0.146,0.146 10 false *1 4.927,0.875 5.073,1.021 0.146,0.146 10 false *4 6.708,0.938 6.854,1.083 0.146,0.146 10 false *2 5.833,2.292 5.979,2.438 0.146,0.146 10 false *3 4.969,1.198 5.115,1.354 0.146,0.156 10 false *a

Text in Illustration
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a 1 mm (0.039 in.) *b Place wrench here
V100135

Molybdenum grease
V100136

Turning direction

SST
09960-20010  (09961-02060, 09961-02010)

CAUTION:

Before working, apply molybdenum grease to the bolt threads and bolt tip of SST.


NOTICE:
·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the dust cover on the toe control link sub-assembly.

·

Do not damage the toe control link sub-assembly.

·

Do not damage the parking brake plate sub-assembly.

·

Do not damage the rear axle carrier.




e.

Put matchmarks on the rear No. 2 suspension toe adjust plate and the rear suspension member.

C256620E02
6.156,0.552 6.625,0.552 false 5.521,2.677 6,2.677 false 6.677,0.469 6.823,0.615 0.146,0.146 10 false *a 6.063,2.594 6.208,2.74 0.146,0.146 10 false *a

Text in Illustration
*a Matchmark - -


f.

Remove the nut, toe adjust cam, rear No. 2 suspension toe adjust plate and the toe control link sub-assembly.