Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2014.05
RM2090E _53 Suspension _060682 TIRE PRESSURE MONITORING _0297611 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU and receiver detects any problems, the tire pressure warning light blinks (stays on after blinking for 1 minute) and tire pressure monitoring is cancelled at the same time. At this time, the ECU stores a DTC in memory.

Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink to output DTCs.

The tire pressure warning ECU and receiver sends the tire pressure warning light illumination request signal to the main body ECU (network gateway ECU) via a direct line. The main body ECU (network gateway ECU) then sends the signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C305303E03
1.458,1.469 4.646,1.844 3.188,0.375 10 false Main Body ECU (Network Gateway ECU) 1.948,2.896 3.854,3.26 1.906,0.365 10 false Combination Meter Assembly 1.958,2.74 2.188,2.979 0.229,0.24 10 false D7 3.875,0.604 4.115,0.802 0.24,0.198 10 false 7 4.802,0.615 4.969,0.813 0.167,0.198 10 false 4 5.042,0.74 5.667,1.01 0.625,0.271 10 false BRDA 3.458,0.75 4.083,1.021 0.625,0.271 10 false RDA 1.469,1.271 1.958,1.438 0.49,0.167 10 false D6 5.01,2.76 5.5,2.927 0.49,0.167 10 false H28 5.021,2.927 6.74,3.323 1.719,0.396 10 false Tire Pressure Warning ECU and Receiver 0.677,3.365 2.469,3.729 1.792,0.365 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.



PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK DTC OUTPUT (B1247)

B

2.CHECK DTC OUTPUT (B1247)

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1247 is not output.




OK

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

NG

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light by using the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light Tire pressure warning light OFF or ON Confirm that the vehicle is stopped, engine idling

OK:

The tire pressure warning light turns on or off in accordance with the GTS operation.




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG