Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2014.05
RM2090E _53 Suspension _060682 TIRE PRESSURE MONITORING _0297611 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (network gateway ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. DTC Detection Condition Trouble Area
B1247 In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds with the ignition switch ON.
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (network gateway ECU)



WIRING DIAGRAM

U190398E02
1.292,0.823 1.594,1.063 0.302,0.24 10 false +B 1.563,0.708 1.865,0.948 0.302,0.24 10 false 7 1.552,1.292 1.854,1.531 0.302,0.24 10 false 1 1.552,2.938 1.854,3.177 0.302,0.24 10 false 12 0.365,3.51 0.667,3.75 0.302,0.24 10 false H28 0.354,3.677 1.865,4.375 1.51,0.698 10 false Tire Pressure Warning ECU and Receiver 5.313,3.396 5.76,3.635 0.448,0.24 10 false D6 5.302,3.563 7.021,4.26 1.719,0.698 10 false Main Body ECU (Network Gateway ECU) 1.323,1.427 1.625,1.667 0.302,0.24 10 false IG 2.458,0.979 3.073,1.219 0.615,0.24 10 false MPX-B 3.677,0.802 4.667,1.156 0.99,0.354 10 false from Battery 3.667,1.396 5.146,1.75 1.479,0.354 10 false from IG1 NO. 1 Relay 2.417,1.573 3.063,1.813 0.646,0.24 10 false ECU IG1 1.177,3.052 1.615,3.292 0.438,0.24 10 false GND 1.573,1.885 1.875,2.125 0.302,0.24 10 false 4 1.552,2.479 1.854,2.719 0.302,0.24 10 false 5 5.51,1.896 5.813,2.135 0.302,0.24 10 false 7 5.5,2.49 5.802,2.729 0.302,0.24 10 false 6 1.094,2.01 1.604,2.25 0.51,0.24 10 false BRDA 1.094,2.604 1.604,2.844 0.51,0.24 10 false BPRG 5.667,2.01 6.177,2.25 0.51,0.24 10 false RDA 5.677,2.594 6.188,2.833 0.51,0.24 10 false PRG

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) -TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector and the D6 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H28-4 (BRDA) - D6-7 (RDA) Always Below 1 Ω
H28-5 (BPRG) - D6-6 (PRG) Always Below 1 Ω
D6-7 (RDA) - Body ground Always 10 kΩ or higher
D6-6 (PRG) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H28-12 (GND) - Body ground Always Below 1 Ω



b.
U147015E04
1.146,1.74 0.802,1.74 true 0.115,0.063 0.458,0.406 0.344,0.344 10 false *a 0.646,1.667 0.906,1.896 0.26,0.229 10 false IG 0.438,1.313 0.823,1.573 0.385,0.26 10 false H28

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H28-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

4.CHECK DTC OUTPUT (B1247)
4.CHECK DTC OUTPUT (B1247)

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1247 is not output.




OK

END

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)