Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM2090E _57 Power Source / Network _060694 POWER DISTRIBUTION _0297664 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 55606 2.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

Hide 82730 4.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
C260461E03
0.177,0.135 0.354,0.313 0.177,0.177 10 false *a 1.365,0.125 1.542,0.302 0.177,0.177 10 false *b

Disengage the clamp.


b.

Disconnect the connector from the power steering ECU assembly.

i.

As shown in the illustration, pull out the lock of the lock lever and turn the lock lever to disconnect the connector.

Text in Illustration
*a Pull out the lock
*b Turn the lock lever



c.

Disconnect the 3 connectors from the power steering ECU.


d.
E247242

Disconnect the 6 front side connectors from the instrument panel junction block assembly indicated as shown in the illustration.


e.
E247243

Remove the bolt, nut and the instrument panel junction block assembly.


f.
B269710

Disconnect the connector indicated as shown in the illustration.


g.
B269712E01
1.493,0.282 1.690,0.484 0.198,0.202 10 *1 1.193,0.783 1.506,0.443 false

Disengage the claw and slide the lever upwards.

Text in Illustration
*1 Lever


h.
B269714

Disconnect the connector indicated as shown in the illustration.


i.

Remove the instrument panel junction block assembly.


Hide 89111 5.REMOVE NETWORK GATEWAY ECU

B195948E07
2.333,1.5 2.896,1.281 false 2.927,1.188 3.115,1.354 0.188,0.167 10 false *1

a.

Press the claw on the instrument panel junction block assembly side, as shown in the illustration, to release the lock.


b.

With the instrument panel junction block assembly side, insert the screwdriver with its tip wrapped in protective tape between the network gateway ECU and the instrument panel junction block assembly.

NOTICE:

Use a blade screwdriver with a diameter of 5.0 to 6.3 mm (0.197 to 0.248 in.), and with a length of 90mm (3.543 in.) or longer.


Text in Illustration
*1 Protective Tape


c.
E184412E03
2.503,1.498 2.367,1.817 false 0.572,1.011 0.865,1.565 false 2.198,1.827 2.354,2.009 0.156,0.181 10 *1 0.798,1.583 0.953,1.764 0.156,0.181 10 *1

Using the screwdriver with its tip wrapped with protective tape, carefully raise the network gateway ECU until the connector becomes disengaged.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Do not twist the screwdriver to raise the network gateway ECU.

·

If any terminals of the connectors, locking parts or cases are deformed or damaged, replace the instrument panel junction block assembly or the network gateway ECU.




d.
B195950E04
0.615,0.698 0.802,0.885 0.188,0.188 10 false (1) 1.594,1.229 1.792,1.406 0.198,0.177 10 false (2)

Raise the network gateway ECU as shown by arrow 1, and then pull it out as shown by arrow 2 in the illustration.

NOTICE:

Do not touch the network gateway ECU connector terminals.