Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2014.05
RM2090E _53 Suspension _060682 TIRE PRESSURE MONITORING _0297611 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179/79  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (network gateway ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. DTC Detection Condition Trouble Area
C2179/79 Communication between the main body ECU (network gateway ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (network gateway ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C305301E03
0.708,1.854 2.594,2.219 1.885,0.365 10 false Main Body ECU (Network Gateway ECU) 4.156,0.875 4.323,1.073 0.167,0.198 10 false 5 2.667,0.854 2.906,1.052 0.24,0.198 10 false 6 4.365,0.99 4.99,1.26 0.625,0.271 10 false BPRG 2.26,0.948 2.885,1.219 0.625,0.271 10 false PRG 0.729,1.698 1.219,1.865 0.49,0.167 10 false D6 4.49,1.667 4.979,1.833 0.49,0.167 10 false H28 4.479,1.823 6.188,2.156 1.708,0.333 10 false Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H28 tire pressure warning ECU and receiver connector and the D6 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H28-5 (BPRG) - D6-6 (PRG) Always Below 1 Ω
H28-5 (BPRG) - Body ground Always 10 kΩ or higher




OK

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

3.REGISTRATION OF TRANSMITTER ID
3.REGISTRATION OF TRANSMITTER ID

NEXT

4.PERFORM INITIALIZATION
4.PERFORM INITIALIZATION

NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC C2179/79 is not output.




OK

END

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)