Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL(for LHD M/T)
RM2090E _54 Brake _060685 BRAKE SYSTEM (OTHER) _0297624 BRAKE PEDAL(for LHD M/T) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD M/T)  ADJUSTMENT  


PROCEDURE

Hide 1.CHECK AND ADJUST BRAKE PEDAL HEIGHT

a.
C260020E04
1.469,1.115 1.292,1.531 false 1.5,2.479 1.323,2.896 false 2,2.833 2.177,3.01 0.177,0.177 10 false *a 1.427,2.26 1.604,2.438 0.177,0.177 10 false *2 1.115,1.531 1.292,1.708 0.177,0.177 10 false *1

Check the pedal height.

Text in Illustration
*1 Clevis Lock Nut
*2 Floor mat
*a Pedal Height

Standard Pedal Height from floor mat
for M/T 145mm
(5.709in.)
for A/T 150mm
(5.906 in.)


b.

Adjust the pedal height.

i.

Remove the No. 1 instrument panel under cover sub-assembly.


ii.

Disconnect the connector from the stop light switch.


iii.

Remove the stop light switch.


iv.

Loosen the push rod clevis lock nut.


v.

Adjust the pedal height by turning the push rod.

Standard Pedal Height from floor mat
for M/T 145mm
(5.709in.)
for A/T 150mm
(5.906 in.)


vi.

Tighten the brake master cylinder push rod clevis lock nut.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


vii.

Install the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).


viii.

Connect the connector to the switch.


ix.

Check that the stop light does not illuminate when the brake pedal is not stepped.



Hide 2.CHECK BRAKE PEDAL FREE PLAY

a.
C111306E03
2.066,1.412 2.315,1.613 0.249,0.201 10 *a

Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.


b.

Depress the pedal until resistance is felt.


c.

Check the pedal free play by measuring the distance between the position in the previous step and the pedal released position.

When the brake pedal is depressed with a force of less than 10 N (1.0 kgf, 2.2 lbf):

0.5 to 2.7 mm

(0.020 to 0.106 in.)


Text in Illustration
*a Pedal Free Play

HINT:

If the free play is out of the specified range, check the protruding amount of the shaft of the stop light switch assembly.



Hide 3.CHECK BRAKE PEDAL RESERVE DISTANCE

a.

Release the parking brake pedal. Start the engine, and when the pressure in the brake booster reaches 66.7 kPa (500 mmHg, 19.6 in.Hg), proceed with the next step.


b.
C219250E02
0.76,1.729 1.375,1.729 false 1.76,1.656 1.917,1.844 0.156,0.188 10 false *a 0.573,1.646 0.74,1.813 0.167,0.167 10 false *1

Depress the pedal and check the pedal reserve distance.

Text in Illustration
*1 Floor mat
*a Pedal Reserve Distance

Standard Pedal Reserve Distance from the floor mat at 490 N (50 kgf, 110.2 lbf):

More than 55 mm (2.165 in.)


If the distance is not as specified, troubleshoot the brake system.

HINT:

Check the brake pedal reserve distance at the same location as that used when checking the brake pedal height.