Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511  Torque Sensor Circuit Malfunction  C1512  Torque Sensor Circuit Malfunction  C1513  Torque Sensor Circuit Malfunction  C1514  Torque Sensor Power Supply Abnormal  C1517  Torque Hold Abnormal  


DESCRIPTION

The torque sensor converts the rotation torque input to the steering wheel into an electrical signal and sends it to the power steering ECU assembly. Based on this signal, the ECU detects steering effort.

DTC Code DTC Detection Condition Trouble Area
C1511 A torque sensor (TRQ1) signal error or stop
·

Steering column assembly (torque sensor)

·

Power steering ECU assembly


C1512 A torque sensor (TRQ2) signal error or stop
C1513 The deviation between torque sensor TRQ1 and TRQ2 exceeds a specified value.
C1514 A torque sensor power supply voltage error
C1517 Temporary control due to a malfunction related to the torque sensor continues for long time.

WIRING DIAGRAM

C261868E02
1.896,3.573 4.646,4.031 2.75,0.458 10 false Steering Column Assembly 4.458,3.5 6.854,3.656 2.396,0.156 10 false z2 4.458,3.667 7.135,4 2.677,0.333 10 false Power Steering ECU Assembly 4.74,1 5.646,1.208 0.906,0.208 10 false TRQV 4.74,2.917 5.656,3.167 0.917,0.25 10 false TRQG 4.74,2.271 5.542,2.469 0.802,0.198 10 false TRQ2 4.74,1.635 5.5,1.813 0.76,0.177 10 false TRQ1 4.573,0.938 4.802,1.083 0.229,0.146 10 false 9 4.521,2.833 4.75,2.979 0.229,0.146 10 false 11 4.521,2.198 5.052,2.354 0.531,0.156 10 false 10 4.573,1.573 4.802,1.719 0.229,0.146 10 false 8 1.708,1.927 3.698,2.125 1.99,0.198 10 false Torque Sensor

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly or steering column assembly is replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - POWER STEERING ECU ASSEMBLY)
a.
U146977E02
0.219,0.042 0.396,0.219 0.177,0.177 10 false *a 1.74,0.385 2.042,0.563 0.302,0.177 10 false z2

Check the connection condition of the z2 torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)

NG

CONNECT CONNECTOR SECURELY

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.
U146978E02
1.875,1.24 1.573,1.792 true 1.958,1.229 2.25,1.771 true 1.938,1.792 2.594,1.969 0.656,0.177 10 false 9 (TRQV) 0.979,1.802 1.677,1.979 0.698,0.177 10 false 11(TRQG) 0.219,0.063 0.396,0.24 0.177,0.177 10 false *a 1.729,0.375 2.031,0.552 0.302,0.177 10 false z2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z2-9 (TRQV) - z2-11 (TRQG) Ignition switch ON 4.5 to 5.5 V


HINT:

When the value is within the specified range, record the value.


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
U146979E02
1.927,1.208 1.573,1.865 true 1.875,1.229 0.823,1.917 true 2.031,1.229 2.344,1.802 true 0.146,1.906 0.854,2.083 0.708,0.177 10 false 11 (TRQG) 1.135,1.885 1.813,2.063 0.677,0.177 10 false 10 (TRQ2) 2.01,1.833 2.729,2.01 0.719,0.177 10 false 8 (TRQ1) 0.219,0.073 0.417,0.25 0.198,0.177 10 false *a 1.729,0.375 2.031,0.552 0.302,0.177 10 false z2

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z2-8 (TRQ1) - z2-11 (TRQG) Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 2.3 to 3.8 V
Engine running, steering wheel turned to left with vehicle stopped 1.2 to 2.7 V
z2-10 (TRQ2) - z2-11 (TRQG) Engine running, steering wheel not turned (without load) 2.3 to 2.7 V
Engine running, steering wheel turned to right with vehicle stopped 1.2 to 2.7 V
Engine running, steering wheel turned to left with vehicle stopped 2.3 to 3.8 V



c.

Calculate the difference between the value recorded when measuring the voltage at terminal TRQV in the previous step, and the sum of the output of torque sensor 1 and torque sensor 2.

OK:

0.3 V or less (Absolute value)


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY