Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1522  Motor Circuit Malfunction  C1523  Motor Circuit Malfunction  C1524  Motor Circuit Malfunction  C1555  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies the current to the power steering motor through the motor circuit.

DTC Code DTC Detection Condition Trouble Area
C1522 A motor current sensor malfunction
·

Steering column assembly

·

Power steering ECU assembly


C1523 An excessively large current deviation
C1524 A short or open in the motor circuit or abnormal voltage or current in the motor circuit
C1555 A motor relay malfunction

WIRING DIAGRAM

C261869E02
0.49,2.552 2.51,3.104 2.021,0.552 10 false Power Steering Motor 4.563,2.563 6.99,2.719 2.427,0.156 10 false z1 4.552,2.74 7.156,3.073 2.604,0.333 10 false Power Steering ECU Assembly 4.792,0.719 4.948,0.875 0.156,0.156 10 false U 4.792,1.313 5.26,1.542 0.469,0.229 10 false V 4.792,1.906 5.25,2.073 0.458,0.167 10 false W 4.552,1.24 4.708,1.396 0.156,0.156 10 false 1 4.563,1.833 4.719,1.99 0.156,0.156 10 false 3 4.563,0.635 4.719,0.792 0.156,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly or steering column assembly is replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER STEERING MOTOR - POWER STEERING ECU ASSEMBLY)
a.
U146980E02
0.219,0.042 0.396,0.219 0.177,0.177 10 false *a 0.865,0.375 1.167,0.552 0.302,0.177 10 false z1

Check the connection condition of the z1 power steering motor connector.

OK:

Power steering motor connector is securely connected and locked to the power steering ECU assembly.


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

2.READ VALUE USING GTS (MOTOR VOLTAGE)

NG

CONNECT CONNECTOR SECURELY

2.READ VALUE USING GTS (MOTOR VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the items "Motor Terminal Volt(U)", "Motor Terminal Volt(V)" and "Motor Terminal Volt(W)" in the Data List and read the value displayed on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Motor Terminal Volt(U) Motor terminal voltage (U phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Motor Terminal Volt(V) Motor terminal voltage (V phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.
Motor Terminal Volt(W) Motor terminal voltage (W phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes between 4 and 35 V The engine is running and the steering wheel is being turned.

Result
Result Proceed to
During steering operation, value changes between 4 and 35 V. A
During steering operation, voltage is not generated or voltage outside specified range is generated. B



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE STEERING COLUMN ASSEMBLY