Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2090E _55 Steering _060689 POWER ASSIST SYSTEMS _0297642 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1528  Motor Rotation Angle Sensor Malfunction  


DESCRIPTION

The rotation angle sensor detects the motor rotation angle and sends this information to the power steering ECU assembly.

DTC Code DTC Detection Condition Trouble Area
C1528 A rotation angle sensor malfunction
·

Rotation angle sensor (built into steering column assembly)

·

Power steering ECU assembly



WIRING DIAGRAM

C261870E02
4.177,3.833 6.583,4 2.406,0.167 10 false z2 4.156,4.021 6.99,4.365 2.833,0.344 10 false Power Steering ECU Assembly 4.281,0.625 5.365,0.917 1.083,0.292 10 false RZV 4.281,1.427 5.375,1.625 1.094,0.198 10 false RZSN 4.281,2.344 5.26,2.542 0.979,0.198 10 false RZCS 4.281,3.219 5.313,3.469 1.031,0.25 10 false RZG 4.042,0.542 4.229,0.698 0.188,0.156 10 false 5 4.021,1.375 4.604,1.552 0.583,0.177 10 false 14 4.021,2.25 4.646,2.406 0.625,0.156 10 false 13 4.042,3.115 4.229,3.271 0.188,0.156 10 false 7 0.719,3.875 2.583,4.469 1.865,0.594 10 false Rotation Angle Sensor

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly or steering column assembly is replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (ROTATION ANGLE SENSOR - POWER STEERING ECU ASSEMBLY)
a.
U146981E02
0.219,0.042 0.396,0.219 0.177,0.177 10 false *a 1.719,0.365 2.021,0.542 0.302,0.177 10 false z2

Check the connection condition of the z2 rotation angle sensor connector.

OK:

Rotation angle sensor connector is securely connected to the power steering ECU assembly.


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

2.READ VALUE USING GTS (MOTOR ROTATION ANGLE)

NG

CONNECT CONNECTOR SECURELY

2.READ VALUE USING GTS (MOTOR ROTATION ANGLE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Motor Rotation Angle Motor rotation angle/
Min.: 0.000 deg
Max.: 360.000 deg
Motor rotation angle value changes from 0 to 360° The engine is running and the steering wheel is being turned.

OK:

During steering operation, motor rotation angle value changes from 0 to 360°.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

3.CHECK STEERING COLUMN ASSEMBLY
3.CHECK STEERING COLUMN ASSEMBLY
a.
U147195E02
2.396,1.385 2.396,1.802 true 2.729,1.385 2.729,1.542 true 2.719,0.573 2.719,0.792 true 2.052,0.583 2.052,0.802 true 0.104,0.052 0.292,0.24 0.188,0.188 10 false *a 1.635,0.26 1.938,0.438 0.302,0.177 10 false z2 2.135,1.823 2.552,2 0.417,0.177 10 false RZCS 2.5,1.573 2.917,1.75 0.417,0.177 10 false RZSN 2.552,0.333 2.885,0.51 0.333,0.177 10 false RZG 1.958,0.333 2.292,0.51 0.333,0.177 10 false RZV

Disconnect the z2 rotation angle sensor connector from the power steering ECU assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-14 (RZSN) - z2-7 (RZG) At 23°C (73°F) 75.2 to 112.8 Ω
z2-5 (RZV) - z2-7 (RZG) At 23°C (73°F) 27.6 to 41.4 Ω
z2-13 (RZCS) - z2-7 (RZG) At 23°C (73°F) 73.6 to 110.4 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rotation Angle Sensor)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY