Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2090E _55 Steering _060690 STEERING COLUMN _0297644 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the SLR+ input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock actuator assembly (steering lock ECU) is determined to be abnormal.

HINT:

The steering lock actuator assembly (steering lock ECU) is not connected to the CAN communication system. However, the steering lock actuator assembly (steering lock ECU) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2782 Either condition is met (1-trip detection logic*1):
·

The steering lock motor activation command circuit has a short circuit.

·

The steering lock motor activation command circuit has an open circuit.


HINT:

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


·

Steering lock actuator assembly (steering lock ECU)

·

Certification ECU (Smart key ECU assembly)

·

Harness or connector


Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P*2 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key)

*1: Only output while a malfunction is present and the engine switch is on (IG).

*2: for Automatic Transmission


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2782
Entry&Start
·

Power Supply Short


-

WIRING DIAGRAM

C220331E21
0.149,3.157 1.759,3.516 1.610,0.360 10 Certification ECU (Smart Key ECU Assembly) 0.149,2.998 0.463,3.172 0.313,0.174 10 D41 5.025,3.157 7.137,3.498 2.112,0.341 10 Steering Lock Actuator Assembly (Steering Lock ECU) 5.025,2.998 5.320,3.172 0.295,0.174 10 D59 0.817,0.803 1.232,0.977 0.415,0.174 10 SLR+ 1.27,0.696 1.472,0.870 0.202,0.174 10 29 5.174,0.696 5.377,0.870 0.202,0.174 10 3 5.38,0.803 5.805,0.977 0.425,0.174 10 SLR+ 5.38,1.97 5.735,2.145 0.355,0.174 10 GND 5.174,1.868 5.377,2.042 0.202,0.174 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off (lock), perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the Service Bulletin.

·

After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D59-1 (SLR+) - Body ground Always Below 1 Ω



c.

Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.


d.

Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P*.

*: for Automatic Transmission



e.
U190320E02
1.833,1.26 1.042,1.719 true 2.302,1.271 2.469,1.719 true 1.458,2.896 2.813,2.677 2.813,2.677 2.646,2.948 true 2.042,4.219 2.042,4.406 true 0.115,0.063 0.292,0.25 0.177,0.188 10 false *a 2.865,2.542 3.042,2.729 0.177,0.188 10 false *b 1.969,4.427 2.146,4.615 0.177,0.188 10 false *c 0.792,1.76 1.198,1.969 0.406,0.208 10 false SLR+ 2.323,1.76 2.698,1.927 0.375,0.167 10 false GND 2.99,4.052 3.365,4.219 0.375,0.167 10 false GND 1.583,0.323 1.885,0.5 0.302,0.177 10 false D59

Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection D59-3 (SLR+) - D59-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

Text in Illustration
*a Component with harness connected
(Steering Lock Actuator Assembly (Steering Lock ECU))
*b Steering lock motor not operating
*c Steering lock motor operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever is in P*, and then open a door.

*: for Automatic Transmission






OK

2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU))
2.CLEAR DTC AND DATA LIST MALFUNCTION RECORD

b.

Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored.

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




NEXT

3.CHECK DTC AND READ VALUE USING GTS (POWER SUPPLY SHORT)
3.CHECK DTC AND READ VALUE USING GTS (POWER SUPPLY SHORT)
a.

Perform the DTC output confirmation operation.


b.

Check if DTC B2782 is output (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).


c.

Use the Data List to check if the steering lock control is functioning properly.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Short Record of malfunction of signal sent to steering lock actuator assembly (motor) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG (Past) OK: No record of malfunction (short circuit)
NG (Past): Record of malfunction (short circuit) exists
This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock actuator assembly (motor).

Result
Result Proceed to
·

B2782 is not output

·

"OK" is displayed on the GTS.


A
·

B2782 is output

·

"NG (Past)" is displayed on the GTS.


B



A

SYSTEM RETURNED TO NORMAL (DTC STORED DUE TO BAD CONNECTION, BUT SYSTEM RETURNED TO NORMAL BY RECONNECTING CONNECTOR)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU))
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.


c.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D41-29 (SLR+) - D59-3 (SLR+) Always Below 1 Ω
D59-3 (SLR+) - Body ground Always 10 kΩ or higher
D41-29 (SLR+) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR