The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) (w/ ID Code Box) or ECM is replaced, the system needs to be initialized and registered. Otherwise, the steering cannot be unlocked and the engine cannot be started.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to unlock steering wheel (Engine cannot start) |
|
- |
When using the GTS with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
After completing repairs, confirm that the problem does not occur.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Before replacing the certification ECU (smart key ECU assembly), steering lock actuator assembly (steering lock ECU) or ID code box (immobiliser code ECU) (w/ ID Code Box), refer to Service Bulletin.
When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
If the steering lock actuator assembly (steering lock ECU) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.
*: for Automatic Transmission
Using the GTS, confirm the output of DTCs for all systems.
No DTCs are output.
When using the GTS with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
OK
NG
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in P*1, check that pressing the engine switch with the brake pedal*1 or clutch pedal*2 released causes the power source mode to change as follows:
*1: for Automatic Transmission
*2: for Manual Transmission
Off → on (ACC) → on (IG) → off
OK
NG
Use the Data List to check if the steering lock request is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Unlock Request Receive*1 | Reception state of steering unlock command signal determined by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
|
OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above |
·
If the unlock signal has not been received, the engine cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Unlock Request Receive*2 | Reception state of steering unlock command signal determined by certification ECU (smart key ECU assembly) / OK or NG
|
OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above |
·
If the unlock signal has not been received, the engine cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
*1: w/ ID Code Box
*2: w/o ID Code Box
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o ID Code Box) | B |
| NG (w/ ID Code Box) | C |
A
B
C
Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D59-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the connection which leads to ground.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D59-7 (B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Steering Lock Actuator Assembly (Steering Lock ECU)) |
OK
NG
Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | D59-3 (SLR+) - D59-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating |
| *a | Component with harness connected
(Steering Lock Actuator Assembly (Steering Lock ECU)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
To lock the steering, turn the engine switch off with the shift lever is in P*, and then open a door.
*: for Automatic Transmission
OK
NG
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is not registered or the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
Reasons for verification failure:
The steering lock actuator assembly (steering lock ECU) or certification ECU (smart key ECU assembly) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK
NG
Replace the steering lock actuator assembly (steering lock ECU) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
Steering is unlocked.
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock actuator assembly / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is not registered or the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
OK
NG
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is not registered or the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
Reasons for verification failure:
The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK
NG
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is not registered or the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
Reasons for verification failure:
The steering lock actuator assembly (steering lock ECU) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK
NG
Replace the steering lock actuator assembly (steering lock ECU) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY).
Perform registration (refer to Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
Steering is unlocked.
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is not registered or the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
OK
NG
Replace the steering lock actuator assembly (steering lock ECU) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY).
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is not registered or the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
OK is displayed on the GTS.
OK
NG