Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2090E _55 Steering _060690 STEERING COLUMN _0297644 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2788  IG2 Signal Malfunction  


DESCRIPTION

This DTC is stored when the steering lock actuator assembly (steering lock ECU) detects an IG2 power supply malfunction.

HINT:

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2788 Mismatch between the steering lock actuator assembly (steering lock ECU) IGN1 input from the LIN communication system and from the direct line (1-trip detection logic*).
·

GAUGE fuse

·

Steering lock actuator assembly (steering lock ECU)

·

Harness or connector


No confirmation operation is necessary (monitoring is continuous).

*: Only output while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. -

Related Data List and Active Test Items
DTC Code Data List Item Active Test Item
B2788 - -

WIRING DIAGRAM

C240290E43
5.375,1.469 5.74,1.656 0.365,0.188 10 false IGN1 5.375,0.656 5.688,0.844 0.313,0.188 10 false LIN 5.375,2.24 5.781,2.427 0.406,0.188 10 false GND 5.156,0.479 5.323,0.667 0.167,0.188 10 false 5 5.156,1.333 5.323,1.521 0.167,0.188 10 false 6 5.156,2.115 5.323,2.302 0.167,0.188 10 false 1 5.042,3.052 5.375,3.24 0.333,0.188 10 false D59 5.031,3.229 7.115,3.594 2.083,0.365 10 false Steering Lock Actuator Assembly (Steering Lock ECU) 0.125,3.042 0.458,3.229 0.333,0.188 10 false D41 0.125,3.198 1.698,3.563 1.573,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.781,3.344 4.375,3.542 1.594,0.198 10 false LIN Communication Line 0.927,0.677 1.24,0.865 0.313,0.188 10 false LIN 1.25,0.479 1.448,0.667 0.198,0.188 10 false 17 3.885,1.635 4.469,1.833 0.583,0.198 10 false GAUGE 1.802,1.438 2.802,1.635 1,0.198 10 false from IG2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off (lock), perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the Service Bulletin.

·

After performing repairs, confirm that no DTCs are output again (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D59-1 (GND) - Body ground Always Below 1 Ω



c.
U190315E02
1.333,1.167 1.094,1.698 true 2.573,1.688 2.333,1.156 true 0.927,1.729 1.292,1.917 0.365,0.188 10 false IGN1 0.094,0 0.49,0.229 0.396,0.229 10 false *a 2.458,1.719 2.823,1.906 0.365,0.188 10 false GND 1.604,0.25 1.927,0.427 0.323,0.177 10 false D59

Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D59-6 (IGN1) - D59-1 (GND) Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Steering Lock Actuator Assembly (Steering Lock ECU))



OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR