Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM2090E _55 Steering _060691 STEERING GEAR / LINKAGE _0297649 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to align the front wheels straight ahead when removing and installing the steering gear assembly.

·

When disconnecting the steering intermediate shaft assembly and the pinion shaft of the steering gear assembly, be sure to place matchmarks before servicing.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEELS

Hide 3.SECURE STEERING WHEEL ASSEMBLY

a.
C260496

Secure the steering wheel assembly with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 48810 6.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C261007

Remove the nut and front stabilizer link assembly LH from the front stabilizer bar.

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.


Hide 48820B 7.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48811 8.REMOVE FRONT STABILIZER BAR

a.
C260500

Remove the 8 bolts, and remove the front stabilizer bar together with the rear body mounting cushion sub-assembly LH and RH from the front suspension cross member.


Hide 45260 9.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C260472E01
1.511,0.7 1.964,0.524 1.964,0.524 1.488,0.623 false 1.982,0.428 2.168,0.590 0.186,0.161 10 *1

Put matchmarks on the steering intermediate shaft assembly and rack and pinion power steering gear assembly.

Text in Illustration
*1 Matchmark


b.

Remove the bolt.


c.

Disconnect the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.


Hide 45047 10.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C260497

Remove the cotter pin and nut.


b.
C260498

Install SST to the tie rod end sub-assembly LH.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the lower ends of the tie rod end sub-assembly LH and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle.

C260499E01
0.433,2.265 0.619,2.426 0.186,0.161 10 *1 1.605,1.52 1.748,1.696 0.144,0.177 10 A 1.605,1.758 1.748,1.935 0.144,0.177 10 B 1.372,0.245 1.558,0.406 0.186,0.161 10 *a 6.481,0.691 6.667,0.852 0.186,0.161 10 *b 6.547,0.35 6.732,0.512 0.186,0.161 10 *b 0.82,1.977 0.82,2.338 0.82,2.338 0.581,2.338 false 1.029,0.594 1.388,0.341 false

Text in Illustration
*1 Center Nut - -
*a String *b Grease Application Area
V100136

Place the wrench here. - -

SST
09960-20010  (09961-02010)

CAUTION:

Apply grease to the bolt threads and the tip of SST.


NOTICE:
·

Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.


·

Be sure to place the wrench on the part indicated in the illustration.


·

Do not damage the front disc brake dust cover.


·

Do not damage the ball joint dust cover.


·

Do not damage the steering knuckle.




Hide 45046 11.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 44250 12.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C260501

Remove the 2 bolts and rack and pinion power steering gear assembly.