Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM2090E _55 Steering _060691 STEERING GEAR / LINKAGE _0297649 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STEERING RACK GUIDE

a.

Apply grease to the steering rack guide spring and the contact surface of the rack guide.


b.

Install the rack guide and the steering rack guide spring.


c.

Apply three bond to 2 or 3 threads of the steering rack guide spring cap.


d.

Temporarily install the steering rack guide spring cap.


Hide 45503 3.INSTALL STEERING RACK END SUB-ASSEMBLY

a.

Using SST, install the steering rack end subassembly.

SST
09922-10010  

C260524E03
1.823,2.083 1.823,2.354 false 0.479,1.625 0.479,1.896 false 5.448,2 5.448,2.417 false 5.333,2.052 5.333,2.24 5.333,2.24 5.448,2.24 false 0.042,0.042 0.24,0.219 0.198,0.177 10 false *A 0.073,0.313 0.26,0.5 0.188,0.188 10 false *a 0.865,0.188 1.042,0.354 0.177,0.167 10 false *c 5.146,0.302 5.333,0.479 0.188,0.177 10 false *c 1.74,0.656 1.906,0.833 0.167,0.177 10 false *d 1.688,2.385 1.99,2.552 0.302,0.167 10 false SST 5.813,0.802 6,0.979 0.188,0.177 10 false *d 3.875,0.313 4.063,0.5 0.188,0.188 10 false *b 0.344,1.896 0.646,2.104 0.302,0.208 10 false SST 5.344,2.427 5.646,2.604 0.302,0.177 10 false SST

Text in Illustration
*A for LHD - -
*a LH Side *b RH Side
*c Turn *d Hold

C260521E04
3.26,1.708 3.26,1.979 false 1.75,2.229 1.75,2.5 false 5.438,1.531 5.438,1.948 false 5.313,1.573 5.313,1.76 5.313,1.76 5.427,1.76 false 0.052,0.063 0.271,0.24 0.219,0.177 10 false *A 0.104,0.458 0.292,0.646 0.188,0.188 10 false *a 3.406,0.063 3.573,0.229 0.167,0.167 10 false *c 4.125,0 4.292,0.188 0.167,0.188 10 false *c 1.292,0.833 1.458,1.01 0.167,0.177 10 false *d 3.125,2.01 3.427,2.219 0.302,0.208 10 false SST 5.375,0.198 5.552,0.365 0.177,0.167 10 false *d 3.854,0.385 4.042,0.573 0.188,0.188 10 false *b 1.615,2.5 1.917,2.708 0.302,0.208 10 false SST 5.302,1.958 5.604,2.167 0.302,0.208 10 false SST

Text in Illustration
*A for RHD - -
*a LH Side *b RH Side
*c Turn *d Hold

HINT:

Using SST, hold the steering rack and install the steering rack end sub-assembly.


Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

NOTICE:
·

Use the formula to calculate special torque values for situations where SST is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn SST in the direction as shown in the illustration.

·

Fix the steering rack firmly in place.




Hide 45535 4.INSTALL NO. 1 STEERING RACK BOOT

HINT:

Use the same procedure for both the LH side and RH side.


a.

Wipe the old grease off of the No. 1 steering rack boot and rack end mating groove.


b.
C057755

Apply silicone grease to the inside of the small opening of a new No. 1 steering rack boot.


c.

Install the No. 1 steering rack boot to the groove on the rack housing.

NOTICE:
·

Be careful not to damage or twist the boot.

·

Make sure that the boot is free of rust and foreign matter.




Hide 45535D 5.INSTALL NO. 1 STEERING RACK BOOT CLAMP

HINT:

Use the same procedure for both the LH side and RH side.


a.
C257760E01
0.539,0.856 0.725,1.017 0.186,0.161 10 *a

Install the new No. 1 steering rack boot clamp to the No. 1 steering rack boot in such a way that the staked part of the clamp is positioned with in the range, as shown in the illustration.

Text in Illustration
*a 150°


b.
F040556E36
1.938,0.875 1.479,0.354 1.479,0.354 1.115,0.354 false 0.76,0.25 1.063,0.396 0.302,0.146 10 false SST

Using SST, tighten a new No. 1 steering rack boot clamp as shown in the illustration.

SST
09521-24010  

Clearance:

2.0 mm (0.079 in.) or less


NOTICE:
·

Be careful not to damage the No. 1 steering rack boot.

·

If the No. 1 steering rack boot is fissured, damaged or deteriorated, replace it with a new one.




Hide 45535B 6.INSTALL STEERING RACK BOOT CLIP

HINT:

Use the same procedure for both the LH side and RH side.


a.

Using pliers, install the steering rack boot clip.


Hide 44250 7.INSPECT RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C370499E01
2.313,0.792 2.823,0.792 false 2.854,0.719 3.167,0.896 0.313,0.177 10 false SST

Using SST, rotate the pinion shaft to see if both the left and the right steering rack boots expand and contract smoothly.

SST
09616-00011  

NOTICE:

Set the pinion shaft at the neutral position after the inspection.


HINT:

If the operation cannot be done as specified, use a new steering rack boot clamp and reinstall the steering rack boots.



Hide 45047 8.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.
C182153E02
0.482,0.998 0.573,0.418 0.573,0.418 1.009,0.418 false 0.679,1.03 0.765,0.418 false 1.046,0.323 1.292,0.486 0.246,0.163 10 *1

Temporarily tighten the lock nut and tie rod end sub-assembly LH to the steering rack end sub-assembly until the matchmarks are aligned.

Text in Illustration
*1 Matchmark

HINT:

After adjusting the front wheel alignment, securely tighten the lock nut.


Torque:
Temporarily tighten : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Securely tighten : 85 N*m (869 kgf*cm, 63 ft.*lbf)


Hide 45046 9.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the procedure as for the LH side.