Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM2090E _56 Audio / Visual / Telematics _060692 AUDIO / VIDEO _0297650 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E249952E02
3.25,2.719 3.896,3.021 0.646,0.302 10 false (Shielded) 1.031,1.698 1.563,1.854 0.531,0.156 10 false USB D+ 0.865,2.135 1.563,2.292 0.698,0.156 10 false PWR GND 5.542,1.573 5.719,1.729 0.177,0.156 10 false 3 5.542,2 5.719,2.156 0.177,0.156 10 false 4 5.542,2.427 5.719,2.583 0.177,0.156 10 false 5 1.677,1.583 1.854,1.74 0.177,0.156 10 false 3 1.677,2.021 1.854,2.177 0.177,0.156 10 false 4 1.677,2.427 1.854,2.583 0.177,0.156 10 false 5 5.229,2.896 5.406,3.052 0.177,0.156 10 false a2 0.25,2.896 0.604,3.052 0.354,0.156 10 false a1 0.25,3.083 2.563,3.385 2.313,0.302 10 false No. 1 Stereo Jack Adapter Assembly 5.229,3.073 6.854,3.375 1.625,0.302 10 false Radio Receiver Assembly 5.76,1.698 6.188,1.854 0.427,0.156 10 false USI+ 5.76,2.115 6.188,2.271 0.427,0.156 10 false USI- 5.76,2.542 6.188,2.698 0.427,0.156 10 false USGI 0.885,0.844 1.563,1 0.677,0.156 10 false USB PWR 5.542,0.729 5.719,0.885 0.177,0.156 10 false 1 1.667,0.74 1.844,0.896 0.177,0.156 10 false 1 5.76,0.833 6.188,0.99 0.427,0.156 10 false UGDI 1.052,1.271 1.552,1.427 0.5,0.156 10 false USB D- 1.677,1.167 1.875,1.323 0.198,0.156 10 false 2 5.76,1.292 6.188,1.448 0.427,0.156 10 false USVI 5.542,1.177 5.719,1.333 0.177,0.156 10 false 2 1.188,2.552 1.563,2.708 0.375,0.156 10 false UJSS

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while before play begins.

·

When using a USB device, files that are copy protected or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).


Result:
Condition Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the radio receiver assembly and No. 1 stereo jack adapter assembly connectors.


b.
U190419E02
1.896,1.448 2.281,1.448 true 2.25,1.781 1.74,1.49 true 1.552,1.5 1.021,1.823 true 2.24,1.969 1.688,1.583 true 0.917,1.469 1.375,1.469 true 1.5,3.938 1.031,3.656 true 1.49,4.125 1.021,4.125 true 1.771,3.938 2.385,3.729 true 1.781,4.125 2.313,4.125 true 1.708,4.271 2.292,4.417 true 1.573,0.375 1.76,0.521 0.188,0.146 10 false a1 2.344,1.385 3.042,1.563 0.698,0.177 10 false PWR GND 0.219,1.385 0.885,1.563 0.667,0.177 10 false USB PWR 0.135,0.125 0.406,0.302 0.271,0.177 10 false *a 0.115,2.625 0.302,2.802 0.188,0.177 10 false *b 2.313,1.708 2.844,1.885 0.531,0.177 10 false USB D+ 0.5,1.792 0.99,1.969 0.49,0.177 10 false USB D- 2.25,1.948 2.646,2.125 0.396,0.177 10 false UJSS 0.708,3.542 1,3.719 0.292,0.177 10 false USI- 2.438,3.625 2.813,3.802 0.375,0.177 10 false UGDI 2.344,4.365 2.719,4.542 0.375,0.177 10 false USGI 0.594,4.042 0.927,4.219 0.333,0.177 10 false USI+ 2.385,4.052 2.74,4.229 0.354,0.177 10 false USVI 1.563,2.865 1.75,3.01 0.188,0.146 10 false a2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-1 (USB PWR) - a2-1 (UGDI) Always Below 1 Ω
a1-2 (USB D-) - a2-2 (USVI) Always Below 1 Ω
a1-3 (USB D+) - a2-3 (USI+) Always Below 1 Ω
a1-4 (PWR GND) - a2-4 (USI-) Always Below 1 Ω
a1-5 (UJSS) - a2-5 (USGI) Always Below 1 Ω
a1-1 (USB PWR) - Body ground Always 10 kΩ or higher
a1-2 (USB D-) - Body ground Always 10 kΩ or higher
a1-3 (USB D+) - Body ground Always 10 kΩ or higher
a1-4 (PWR GND) - Body ground Always 10 kΩ or higher
a1-5 (UJSS) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Radio Receiver Assembly)



OK

3.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the radio receiver assembly connector.


b.
U190418E02
1.458,2.094 0.99,1.792 true 1.979,2.083 2.375,2.083 true 1.646,0.896 1.833,1.042 0.188,0.146 10 false a1 0.281,1.656 0.958,1.802 0.677,0.146 10 false USB PWR 0.146,0.115 0.406,0.26 0.26,0.146 10 false *a 2.458,2 3.156,2.146 0.698,0.146 10 false PWR GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a1-1 (USB PWR) - a1-4 (PWR GND) Ignition switch ACC 5 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device.

Ensure that backup music data is available before performing this operation.


OK:

Malfunction disappears.




OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).





NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names are displayed on the screen.

OK:

Malfunction disappears.




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE