Home › Power Source / Network › POWER DISTRIBUTION › ELECTRIC POWER CONTROL SYSTEM
RM2090E _57 Power Source / Network _060694 POWER DISTRIBUTION _0297662 ELECTRIC POWER CONTROL SYSTEM C

POWER DISTRIBUTION  ELECTRIC POWER CONTROL SYSTEM  B1011  Battery Power Supply Control Circuit  


DESCRIPTION

B1011 is stored when a malfunction is detected in the BMPX circuit.


HINT:

In some cases, none of the functions of the main body ECU (network gateway ECU) may function when B1012 is stored together with B1011.


DTC No. DTC Detection Condition Trouble Area
B1011 When BMPX voltage is 8.3 V or less, or 16.7 V or more (BMPX circuit malfunction)
·

Main body ECU (network gateway ECU)

·

Instrument panel junction block assembly

·

Harness or connector



WIRING DIAGRAM

E249070E05
2.135,0.74 2.344,0.896 0.208,0.156 10 false 19 4.865,0.729 5.052,0.885 0.188,0.156 10 false 32 2.135,0.917 2.354,1.063 0.219,0.146 10 false 3C 4.833,0.917 5.073,1.083 0.24,0.167 10 false MB 4.854,2.667 5.042,2.813 0.188,0.146 10 false 11 4.833,2.833 5.073,3 0.24,0.167 10 false MB 2.135,2.646 2.333,2.813 0.198,0.167 10 false 18 2.135,2.833 2.344,3 0.208,0.167 10 false 3B 0.313,0.927 1.115,1.125 0.802,0.198 10 false from Battery 1.479,1.063 1.917,1.24 0.438,0.177 10 false MPX-B 6.104,2.198 6.208,2.354 0.104,0.156 10 false 1 6.063,2.375 6.271,2.542 0.208,0.167 10 false D6 6.104,2.656 6.219,2.813 0.115,0.156 10 false 4 6.031,2.833 6.313,3 0.281,0.167 10 false A73 4.729,3.542 6.344,3.896 1.615,0.354 10 false Main Body ECU (Network Gateway ECU) 2.396,3.292 4.021,3.677 1.625,0.385 10 false Instrument Panel Junction Block Assembly 5.188,0.927 5.635,1.104 0.448,0.177 10 false BMPX 5.177,2.844 5.5,3.01 0.323,0.167 10 false GND 5.656,2.406 5.958,2.573 0.302,0.167 10 false GND 5.656,2.865 5.969,3.021 0.313,0.156 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>POWER DISTRIBUTION>ELECTRIC POWER CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1011 is output A
DTC is not output B



A

3.CHECK HARNESS AND CONNECTOR (BMPX VOLTAGE)

B

3.CHECK HARNESS AND CONNECTOR (BMPX VOLTAGE)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.
U147266E03
1.604,0.229 1.813,0.396 0.208,0.167 10 false 3C 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
3C-19 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (ECU GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECU GROUND)
a.

Disconnect the D6 and A73 main body ECU (network gateway ECU) connector.


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
D6-1 (GND) - Body ground Always Below 1 Ω
A73-4 (GND) - Body ground Always Below 1 Ω
3B-18 - Body ground Always Below 1 Ω




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

U147267E03
3.063,2.167 3.063,2.333 true 5.042,2.167 5.042,2.333 true 2.042,0.229 2.25,0.385 0.208,0.156 10 false 3B 4.875,0.219 5.083,0.375 0.208,0.156 10 false 3C 3.469,1.677 3.719,1.833 0.25,0.156 10 false MB 0.146,0.073 0.333,0.26 0.188,0.188 10 false *a 2.906,2.375 3.271,2.542 0.365,0.167 10 false GND 4.823,2.354 5.271,2.552 0.448,0.198 10 false BMPX

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
3C-19 - MB-32 (BMPX) Always Below 1 Ω
3B-18 - MB-11 (GND) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY