Home › Power Source / Network › POWER DISTRIBUTION › ELECTRIC POWER CONTROL SYSTEM
RM2090E _57 Power Source / Network _060694 POWER DISTRIBUTION _0297662 ELECTRIC POWER CONTROL SYSTEM C

POWER DISTRIBUTION  ELECTRIC POWER CONTROL SYSTEM  B1014  ACC Power Supply Circuit  


DESCRIPTION

B1014 is stored when a malfunction is detected in the ACC circuit.


DTC No. DTC Detection Condition Trouble Area
B1014 When ACC voltage is 8.3 V or less, or 16.7 V or more (ACC circuit malfunction)
·

Main body ECU (network gateway ECU)

·

Instrument panel junction block assembly

·

Harness or connector



WIRING DIAGRAM

E249071E06
1.917,1.188 2.115,1.333 0.198,0.146 10 false 20 1.948,0.719 2.083,0.875 0.135,0.156 10 false 1 4.885,0.74 5.031,0.885 0.146,0.146 10 false 9 1.917,0.906 2.125,1.063 0.208,0.156 10 false 3E 4.823,0.917 5.063,1.083 0.24,0.167 10 false MB 4.833,2.635 5.021,2.792 0.188,0.156 10 false 11 4.823,2.833 5.073,3 0.25,0.167 10 false MB 1.917,1.375 2.125,1.531 0.208,0.156 10 false 3A 1.917,1.729 2.104,1.875 0.188,0.146 10 false 12 1.917,1.906 2.115,2.073 0.198,0.167 10 false 3A 1.917,2.188 2.115,2.333 0.198,0.146 10 false 13 1.917,2.375 2.115,2.552 0.198,0.177 10 false 3A 1.917,2.656 2.094,2.802 0.177,0.146 10 false 18 1.917,2.833 2.115,2.99 0.198,0.156 10 false 3B 2.927,1.688 3.323,1.865 0.396,0.177 10 false ACC1 0.479,0.896 1.281,1.094 0.802,0.198 10 false from Battery 0.229,1.375 1.281,1.563 1.052,0.188 10 false from ACC Circuit 3.823,1.073 4.469,1.26 0.646,0.188 10 false ECU ACC 6.083,2.198 6.229,2.344 0.146,0.146 10 false 1 6.063,2.375 6.26,2.542 0.198,0.167 10 false D6 6.094,2.646 6.25,2.802 0.156,0.156 10 false 4 6.031,2.833 6.313,3 0.281,0.167 10 false A73 2.188,3.323 3.813,3.677 1.625,0.354 10 false Instrument Panel Junction Block Assembly 5.177,0.917 5.625,1.229 0.448,0.313 10 false ACC 5.146,2.833 5.458,3.01 0.313,0.177 10 false GND 5.635,2.365 5.948,2.531 0.313,0.167 10 false GND 5.635,2.833 5.948,3 0.313,0.167 10 false GND 4.74,3.5 6.354,3.865 1.615,0.365 10 false Main Body ECU (Network Gateway ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>POWER DISTRIBUTION>ELECTRIC POWER CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1014 is output A
DTC is not output B



A

3.CHECK HARNESS AND CONNECTOR (VOLTAGE)

B

3.CHECK HARNESS AND CONNECTOR (VOLTAGE)
a.

Disconnect the 3A and 3E instrument panel junction block assembly connector.


b.
U147269E03
1.635,0.344 1.844,0.51 0.208,0.167 10 false 3A 1.646,1.969 1.875,2.125 0.229,0.156 10 false 3E 0.094,0.042 0.271,0.229 0.177,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-20 - Body ground Ignition switch ACC 11 to 14 V
3E-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

U147271E01
1.759,0.237 2.054,0.393 0.295,0.156 10 3B 1.717,1.47 2.012,1.626 0.295,0.156 10 3E 4.552,1.666 4.847,1.822 0.295,0.156 10 MB 4.981,0.237 5.277,0.393 0.295,0.156 10 3A 0.098,0.059 0.436,0.376 0.338,0.317 10 *a 3.959,2.155 3.833,2.34 false 3.678,2.354 3.999,2.515 0.321,0.161 10 ACC 4.149,2.155 4.276,2.34 false 4.129,2.354 4.480,2.515 0.350,0.161 10 GND

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - MB-9 (ACC) No battery voltage is applied across terminals 3A-20 and 3A-12 10 kΩ or higher
3E-1 - MB-9 (ACC) Battery voltage is applied across terminals 3A-20 and 3A-12 Below 1 Ω
3B-18 - MB-11 (GND) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY