Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "CAN Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Steering angle sensor (spiral cable sub-assembly) branch line or connector

·

Power source circuit of steering angle sensor (spiral cable sub-assembly)

·

Steering angle sensor (spiral cable sub-assembly) ground circuit

·

Steering angle sensor (spiral cable sub-assembly)



WIRING DIAGRAM

C262674E06
2.354,1.063 2.26,0.458 2.26,0.458 2.052,0.458 false 4.031,1.063 4.125,0.458 4.125,0.458 4.333,0.458 false 3.583,3.063 4.01,3.229 0.427,0.167 10 false CANH 4.104,3.063 4.531,3.229 0.427,0.167 10 false CANL 0.615,0.396 2.042,0.729 1.427,0.333 10 false CAN NO. 1 JUNCTION CONNECTOR 4.406,0.396 5.833,0.729 1.427,0.333 10 false CAN NO. 2 JUNCTION CONNECTOR 5.563,3.969 6.385,4.156 0.823,0.188 10 false Trouble Area 3.094,0.396 3.458,0.573 0.365,0.177 10 false DLC3 1.396,5.063 3.208,5.25 1.813,0.188 10 false : CAN Main Bus Line (CANH) 1.385,5.375 3.167,5.552 1.781,0.177 10 false : CAN Main Bus Line (CANL) 4.354,5.083 6.021,5.271 1.667,0.188 10 false : CAN Branch Line (CANH) 4.354,5.365 6.031,5.552 1.677,0.188 10 false : CAN Branch Line (CANL) 0.271,2.604 0.604,2.771 0.333,0.167 10 false ECM 2.719,4.26 4.573,4.781 1.854,0.521 10 false STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) 5.635,2.615 6.969,3.135 1.333,0.521 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.813,1.969 1.208,2.146 0.396,0.177 10 false 120 Ω 5.917,1.969 6.313,2.146 0.396,0.177 10 false 120 Ω 2.729,4.083 3.01,4.25 0.281,0.167 10 false D56 3.188,3.427 3.292,3.604 0.104,0.177 10 false 4 4.792,3.417 4.896,3.604 0.104,0.188 10 false 1 3.875,2.833 3.979,3.01 0.104,0.177 10 false 3 4.26,2.833 4.385,3.021 0.125,0.188 10 false 2 3.354,3.531 3.521,3.698 0.167,0.167 10 false IG 2.188,3.688 2.76,3.854 0.573,0.167 10 false ECU IG1 4.427,3.552 4.729,3.719 0.302,0.167 10 false ESS 0.063,0.052 0.719,0.25 0.656,0.198 12 false for RHD:

C262674E07
2.365,1.063 2.271,0.458 2.271,0.458 2.063,0.458 false 4.031,1.063 4.125,0.458 4.125,0.458 4.333,0.458 false 0.625,0.417 2.052,0.76 1.427,0.344 10 false CAN NO. 1 JUNCTION CONNECTOR 4.385,0.396 5.813,0.74 1.427,0.344 10 false CAN NO. 2 JUNCTION CONNECTOR 5.552,3.938 6.365,4.125 0.813,0.188 10 false Trouble Area 3.115,0.396 3.479,0.563 0.365,0.167 10 false DLC3 1.385,5.063 3.188,5.25 1.802,0.188 10 false : CAN Main Bus Line (CANH) 1.385,5.385 3.177,5.573 1.792,0.188 10 false : CAN Main Bus Line (CANL) 4.375,5.063 6.042,5.26 1.667,0.198 10 false : CAN Branch Line (CANH) 4.365,5.385 5.99,5.573 1.625,0.188 10 false : CAN Branch Line (CANL) 5.656,2.594 5.99,2.76 0.333,0.167 10 false ECM 2.729,4.24 4.552,4.76 1.823,0.521 10 false STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) 0.094,2.604 2,2.958 1.906,0.354 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.813,1.969 1.208,2.146 0.396,0.177 10 false 120 Ω 5.917,1.979 6.313,2.156 0.396,0.177 10 false 120 Ω 2.74,4.073 3.021,4.25 0.281,0.177 10 false D56 3.177,3.427 3.281,3.604 0.104,0.177 10 false 4 4.781,3.427 4.875,3.604 0.094,0.177 10 false 1 3.865,2.854 3.969,3.031 0.104,0.177 10 false 3 4.26,2.854 4.375,3.021 0.115,0.167 10 false 2 3.354,3.542 3.521,3.698 0.167,0.156 10 false IG 2.177,3.688 2.74,3.854 0.563,0.167 10 false ECU IG1 4.427,3.563 4.74,3.729 0.313,0.167 10 false ESS 3.594,3.063 4.021,3.229 0.427,0.167 10 false CANH 4.094,3.063 4.521,3.229 0.427,0.167 10 false CANL 0.063,0.063 0.698,0.26 0.635,0.198 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 2 seconds,

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U147057E03
1.354,1.229 0.979,1.615 true 1.771,1.219 2.156,1.604 true 1.573,0.385 1.865,0.542 0.292,0.156 10 false D56 2.198,1.563 2.625,1.719 0.427,0.156 10 false CANH 0.594,1.583 0.979,1.75 0.385,0.167 10 false CANL 0.083,0.031 0.26,0.208 0.177,0.177 10 false *a

Disconnect the D56 steering angle sensor (spiral cable sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-3 (CANH) - D56-2 (CANL) Cable disconnected from negative (-) battery terminal 57 to 63 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U147058E01
1.558,0.362 1.854,0.518 0.295,0.156 10 D56 0.291,1.54 0.713,1.696 0.423,0.156 10 ESS 0.082,0.035 0.378,0.191 0.295,0.156 10 *a 1.071,1.229 0.689,1.611 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-1 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


b.

Connect the cable to the negative (-) battery terminal.


c.
U147059E01
1.558,0.362 1.854,0.518 0.295,0.156 10 D56 2.509,1.54 2.932,1.696 0.423,0.156 10 IG1 0.082,0.035 0.378,0.191 0.295,0.156 10 *a 2.088,1.229 2.47,1.611 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D56-4 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))



OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)