Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on the "CAN Bus Check" screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" (See page (Click here))


·

Skid control ECU (brake actuator assembly) main line or connector

·

Power source circuit of skid control ECU (brake actuator assembly)

·

Skid control ECU (brake actuator assembly) ground circuit

·

Skid control ECU



WIRING DIAGRAM

C262672E02
1.792,4.198 1.698,4.927 1.698,4.927 1.49,4.927 false 3.344,4.219 3.219,5.26 3.219,5.26 3.031,5.26 false 5.208,5.042 6,5.229 0.792,0.188 10 false Trouble Area 3.188,1.719 3.583,1.896 0.396,0.177 10 false DLC3 0.99,0.292 2.813,0.49 1.823,0.198 10 false : CAN Main Bus Line (CANH) 0.99,0.625 2.792,0.844 1.802,0.219 10 false : CAN Main Bus Line (CANL) 0.99,0.979 2.656,1.177 1.667,0.198 10 false : CAN Branch Line (CANH) 1.01,1.313 2.656,1.5 1.646,0.188 10 false : CAN Branch Line (CANL) 0.208,4.271 0.542,4.438 0.333,0.167 10 false ECM 0.031,4.875 1.469,5.24 1.438,0.365 10 false CAN NO. 1 JUNCTION CONNECTOR 4.698,4.281 6.615,4.646 1.917,0.365 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 1.563,5.177 3.01,5.51 1.448,0.333 10 false CAN NO. 2 JUNCTION CONNECTOR 5.271,2.177 5.594,2.354 0.323,0.177 10 false +BM 5.177,3.49 5.594,3.667 0.417,0.177 10 false GND2 5.188,3.844 5.594,4.021 0.406,0.177 10 false GND1 5.323,2.594 5.604,2.771 0.281,0.177 10 false +BS 5.344,3.042 5.594,3.219 0.25,0.177 10 false IG1 4.479,2.75 4.969,2.927 0.49,0.177 10 false CANH 4.49,3.365 4.896,3.542 0.406,0.177 10 false CANL 0.5,3.625 0.896,3.802 0.396,0.177 10 false 120 Ω 4.531,3.656 4.927,3.833 0.396,0.177 10 false 120 Ω 4.406,4.281 4.615,4.448 0.208,0.167 10 false A5 5.667,2.479 5.844,2.656 0.177,0.177 10 false 25 5.656,2.927 5.854,3.104 0.198,0.177 10 false 28 5.667,2.073 5.823,2.25 0.156,0.177 10 false 1 5.656,3.354 5.823,3.531 0.167,0.177 10 false 13 5.667,3.719 5.854,3.896 0.188,0.177 10 false 38 4.26,2.708 4.427,2.885 0.167,0.177 10 false 26 4.24,3.354 4.438,3.531 0.198,0.177 10 false 14 6.177,2.344 6.885,2.51 0.708,0.167 10 false ABS NO. 1 6.188,2.771 6.896,2.938 0.708,0.167 10 false ABS NO. 2 6.26,3.208 6.865,3.375 0.604,0.167 10 false ECU IG1 0.063,0.021 0.719,0.219 0.656,0.198 12 false for RHD:

C262673E05
1.802,4.208 1.708,4.938 1.708,4.938 1.5,4.938 false 3.333,4.219 3.208,5.26 3.208,5.26 3.021,5.26 false 5.271,2.198 5.594,2.375 0.323,0.177 10 false +BM 5.188,3.479 5.604,3.656 0.417,0.177 10 false GND2 5.188,3.854 5.594,4.031 0.406,0.177 10 false GND1 5.313,2.615 5.594,2.792 0.281,0.177 10 false +BS 5.354,3.042 5.604,3.219 0.25,0.177 10 false IG1 4.479,2.729 4.969,2.906 0.49,0.177 10 false CANH 4.479,3.385 4.969,3.563 0.49,0.177 10 false CANL 4.521,3.625 4.917,3.802 0.396,0.177 10 false 120 Ω 0.073,4.844 1.5,5.188 1.427,0.344 10 false CAN NO. 2 JUNCTION CONNECTOR 1.594,5.177 3,5.521 1.406,0.344 10 false CAN NO. 1 JUNCTION CONNECTOR 5.219,5.031 6.021,5.219 0.802,0.188 10 false Trouble Area 1.875,1.74 2.24,1.906 0.365,0.167 10 false DLC3 1.01,0.281 2.802,0.469 1.792,0.188 10 false : CAN Main Bus Line (CANH) 1,0.635 2.792,0.833 1.792,0.198 10 false : CAN Main Bus Line (CANL) 1,0.969 2.698,1.156 1.698,0.188 10 false : CAN Branch Line (CANH) 1,1.302 2.667,1.479 1.667,0.177 10 false : CAN Branch Line (CANL) 0.198,4.24 0.521,4.406 0.323,0.167 10 false ECM 4.635,4.292 6.552,4.635 1.917,0.344 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.438,3.625 0.833,3.802 0.396,0.177 10 false 120 Ω 4.427,4.292 4.646,4.458 0.219,0.167 10 false A5 5.656,2.479 5.833,2.656 0.177,0.177 10 false 25 5.646,2.927 5.844,3.104 0.198,0.177 10 false 28 5.656,2.063 5.813,2.24 0.156,0.177 10 false 1 5.656,3.365 5.823,3.542 0.167,0.177 10 false 13 5.656,3.729 5.906,3.906 0.25,0.177 10 false 38 4.25,2.74 4.417,2.917 0.167,0.177 10 false 26 4.271,3.375 4.469,3.552 0.198,0.177 10 false 14 6.177,2.344 6.885,2.51 0.708,0.167 10 false ABS NO. 1 6.188,2.76 6.896,2.927 0.708,0.167 10 false ABS NO. 2 6.25,3.198 6.854,3.365 0.604,0.167 10 false ECU IG1 0.063,0.042 0.698,0.24 0.635,0.198 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U147125E04
1.292,0.802 0.99,1.115 true 1.188,1.615 0.906,1.344 true 0.188,1.083 0.406,1.25 0.219,0.167 10 false A5 1.323,0.656 1.729,0.813 0.406,0.156 10 false CANL 1.219,1.563 1.646,1.708 0.427,0.146 10 false CANH 0.177,0.052 0.333,0.229 0.156,0.177 10 false *a

Disconnect the A5 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-26 (CANH) - A5-14 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

2.CHECK FOR OPEN IN CAN BUS LINES (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) MAIN LINE)

2.CHECK FOR OPEN IN CAN BUS LINES (POWER SOURCE CIRCUIT)
a.
U147126E01
0.228,1.074 0.524,1.230 0.295,0.156 10 A5 1.5,0.232 2.102,0.388 0.602,0.156 10 GND2 1.763,1.67 2.430,1.826 0.667,0.156 10 GND1 0.179,0.055 0.475,0.211 0.295,0.156 10 *a 2.284,1.752 2.691,1.345 false 2.035,0.318 2.671,0.954 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-13 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A5-38 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


b.

Connect the cable to the negative (-) battery terminal.


c.
U147127E03
0.771,0.958 1.177,0.552 true 0.719,1.354 1.354,1.99 true 1.458,1.635 1.188,1.365 true 0.188,1.083 0.417,1.24 0.229,0.156 10 false A5 1.229,0.448 1.583,0.604 0.354,0.156 10 false +BM 1.5,1.594 1.75,1.76 0.25,0.167 10 false IG1 0.146,0.104 0.313,0.302 0.167,0.198 10 false *a 1.406,1.906 1.729,2.073 0.323,0.167 10 false +BS

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-1 (+BM) - Body ground Ignition switch off 11 to 14 V
A5-25 (+BS) - Body ground Ignition switch off 11 to 14 V
A5-28 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)