There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
Main body ECU (network gateway ECU) ·
Combination meter assembly ·
Certification ECU (smart key ECU assembly)*1 ·
ECM ·
TCM*2 ·
Skid control ECU (brake actuator assembly) ·
Steering angle sensor (spiral cable sub-assembly) ·
Power steering ECU assembly ·
Air conditioning control assembly*3 ·
Air bag ECU assembly ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector |
*1: w/ Entry and Start System
*2: for Automatic Transmission System
*3: for Automatic Air Conditioning System
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| D43-1 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | CAN No. 1 junction connector |
| D43-12 - D10-16 (BAT) | |||
| D43-2 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| D43-13 - D10-16 (BAT) | |||
| D43-3 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (network gateway ECU) |
| D43-14 - D10-16 (BAT) | |||
| D43-4 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Certification ECU (smart key ECU assembly) |
| D43-15 - D10-16 (BAT) | |||
| D43-5 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | DLC3 |
| D43-16 - D10-16 (BAT) | |||
| D43-6 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Steering angle sensor (spiral cable sub-assembly) |
| D43-17 - D10-16 (BAT) | |||
| D43-7 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | PSP (option connector) |
| D43-18 - D10-16 (BAT) | |||
| D43-8 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air bag ECU assembly |
| D43-19 - D10-16 (BAT) | |||
| D43-9 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| D43-20 - D10-16 (BAT) | |||
| D43-10 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning control assembly |
| D43-21 - D10-16 (BAT) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
| *c | to Combination Meter Assembly |
| *d | to Main Body ECU (Network Gateway ECU) |
| *e | to Certification ECU (Smart Key ECU Assembly) |
| *f | to DLC3 |
| *g | to Steering Angle Sensor (Spiral Cable Sub-assembly) |
| *h | to PSP (Option Connector) |
| *i | to Air Bag ECU Assembly |
| *j | to ECM |
| *k | to Air Conditioning Control Assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No. 1 junction connector main line) | B |
| NG (ECM main line) | C |
| NG (ECU or sensor branch line) | D |
| NG (DLC3 branch line or PSP (option connector) branch line) | E |
A
B
C
D
E
Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A17-5 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | TCM |
| A17-16 - D10-16 (BAT) | |||
| A17-6 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Skid control ECU (brake actuator assembly) |
| A17-17 - D10-16 (BAT) | |||
| A17-7 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | CAN No. 2 junction connector |
| A17-18 - D10-16 (BAT) | |||
| A17-8 - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power steering ECU assembly |
| A17-19 - D10-16 (BAT) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to TCM |
| *c | to Skid Control ECU (Brake Actuator Assembly) |
| *d | to CAN No. 2 Junction Connector |
| *e | to Power Steering ECU Assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No. 2 junction connector main line) | B |
| NG (skid control ECU (brake actuator assembly) main line) | C |
| NG (ECU or sensor branch line) | D |
A
B
C
D
Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).
Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.
If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D10-6 (CANH) - D10-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| D10-14 (CANL) - D10-16 (BAT) |
| *1 | DLC3 |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
OK
NG