Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Main body ECU (network gateway ECU)

·

Combination meter assembly

·

Certification ECU (smart key ECU assembly)*1

·

ECM

·

TCM*2

·

Skid control ECU (brake actuator assembly)

·

Steering angle sensor (spiral cable sub-assembly)

·

Power steering ECU assembly

·

Air conditioning control assembly*3

·

Air bag ECU assembly

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: w/ Entry and Start System

*2: for Automatic Transmission System

*3: for Automatic Air Conditioning System

WIRING DIAGRAM

C261306E02
0.469,0.094 0.677,0.25 0.208,0.156 10 false A5 0.458,0.271 2.375,0.625 1.917,0.354 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.26,1.792 2.24,1.969 1.979,0.177 10 false NO. 1 JUNCTION CONNECTOR 5,0.125 6.844,0.302 1.844,0.177 10 false : CAN Main Bus Line (CANH) 5.01,0.51 6.875,0.688 1.865,0.177 10 false : CAN Main Bus Line (CANL) 5.01,0.885 6.99,1.063 1.979,0.177 10 false : CAN Branch Bus Line (CANH) 5.021,1.292 7.021,1.469 2,0.177 10 false : CAN Branch Bus Line (CANL) 0.26,1.615 0.563,1.792 0.302,0.177 10 false A17 0.375,4.708 2.365,4.885 1.99,0.177 10 false NO. 2 JUNCTION CONNECTOR 0.375,4.521 0.677,4.698 0.302,0.177 10 false D43 3.802,0.875 3.979,1.042 0.177,0.167 10 false 26 2.771,0.885 2.927,1.052 0.156,0.167 10 false 14 3.802,1.51 3.948,1.677 0.146,0.167 10 false 6 2.771,1.521 2.938,1.677 0.167,0.156 10 false 17 5.5,5.458 5.719,5.635 0.219,0.177 10 false D7 4.813,4.542 5.042,4.688 0.229,0.146 10 false BR 4.802,5.271 5.208,5.427 0.406,0.156 10 false BR-W 3.823,1.177 4.063,1.344 0.24,0.167 10 false BR 2.646,1.177 2.906,1.333 0.26,0.156 10 false B-R 3.802,3.438 3.927,3.615 0.125,0.177 10 false 7 2.771,3.448 2.948,3.615 0.177,0.167 10 false 18 3.792,4.313 3.906,4.49 0.115,0.177 10 false 1 2.76,4.323 2.938,4.49 0.177,0.167 10 false 12 3.844,3.844 4.146,4.021 0.302,0.177 10 false W-B 2.646,3.854 2.917,4.021 0.271,0.167 10 false R-Y 1.781,2.5 1.917,2.667 0.135,0.167 10 false B 1.76,3.24 1.917,3.417 0.156,0.177 10 false W 4.354,4.615 4.49,4.771 0.135,0.156 10 false 2 4.354,5.188 4.542,5.344 0.188,0.156 10 false 13 5.365,4.594 5.479,4.771 0.115,0.177 10 false 6 5.375,5.198 5.479,5.375 0.104,0.177 10 false 7 1.26,2.573 1.375,2.74 0.115,0.167 10 false 1 1.271,3.188 1.396,3.365 0.125,0.177 10 false 7 2.25,2.573 2.375,2.74 0.125,0.167 10 false 8 2.208,3.156 2.396,3.333 0.188,0.177 10 false 19 0.083,3.458 0.365,3.625 0.281,0.167 10 false A15 0.073,3.635 1.354,3.979 1.281,0.344 10 false POWER STEERING ECU ASSEMBLY 5.5,5.625 6.99,5.969 1.49,0.344 10 false COMBINATION METER ASSEMBLY 5.5,2.635 5.781,2.792 0.281,0.156 10 false A18 4.76,1.708 5.063,1.865 0.302,0.156 10 false B-W 4.854,2.438 4.979,2.615 0.125,0.177 10 false L 4.385,1.781 4.51,1.948 0.125,0.167 10 false 5 4.365,2.365 4.542,2.552 0.177,0.188 10 false 16 5.292,1.802 5.469,1.948 0.177,0.146 10 false 29 5.292,2.354 5.448,2.521 0.156,0.167 10 false 28 5.5,2.823 5.948,2.99 0.448,0.167 10 false TCM*1 5.167,7.51 5.458,7.677 0.292,0.167 10 false D41 4.833,6.583 4.979,6.75 0.146,0.167 10 false G 4.854,7.313 5,7.49 0.146,0.177 10 false R 4.385,6.656 4.51,6.833 0.125,0.177 10 false 4 4.354,7.25 4.531,7.427 0.177,0.177 10 false 15 5.313,6.646 5.479,6.823 0.167,0.177 10 false 14 5.313,7.271 5.479,7.438 0.167,0.167 10 false 15 1.792,5.333 1.906,5.521 0.115,0.188 10 false P 1.75,6.083 1.969,6.24 0.219,0.156 10 false LG 1.271,5.438 1.448,5.594 0.177,0.156 10 false 14 1.281,6.01 1.458,6.177 0.177,0.167 10 false 13 2.24,5.406 2.375,5.583 0.135,0.177 10 false 3 2.188,6.01 2.365,6.188 0.177,0.177 10 false 14 0.063,6.271 0.281,6.427 0.219,0.156 10 false D5 0.052,6.438 1.969,6.781 1.917,0.344 10 false MAIN BODY ECU (NETWORK GATEWAY ECU) 5.156,7.688 7.042,8.052 1.885,0.365 10 false CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)*2 0.125,7.844 2.563,8.031 2.438,0.188 10 false *1 : for Automatic Transmission System 0.167,7.5 1.396,7.688 1.229,0.188 10 false x : Suspected Area 0.125,8.156 2.042,8.333 1.917,0.177 10 false *2 : w/ Entry and Start System 3.177,0.115 3.563,0.281 0.385,0.167 10 false 120 Ω 0.76,2.573 1.167,2.729 0.406,0.156 10 false CANH 0.792,3.177 1.177,3.344 0.385,0.167 10 false CANL 0.76,5.438 1.188,5.594 0.427,0.156 10 false CANH 0.781,6.01 1.167,6.167 0.385,0.156 10 false CANL 3.813,0.677 4.219,0.823 0.406,0.146 10 false CANH 2.531,0.677 2.896,0.833 0.365,0.156 10 false CANL 5.542,6.667 5.958,6.823 0.417,0.156 10 false CANH 5.542,7.24 5.927,7.406 0.385,0.167 10 false CANL 5.531,4.615 5.958,4.771 0.427,0.156 10 false CANH 5.542,5.198 5.927,5.365 0.385,0.167 10 false CANL 5.552,1.781 5.969,1.938 0.417,0.156 10 false CANH 5.552,2.365 5.979,2.542 0.427,0.177 10 false CANL

C261307E02
4.396,6.031 4.74,6.208 0.344,0.177 10 false ECM 0.26,0.354 2.229,0.521 1.969,0.167 10 false NO. 2 JUNCTION CONNECTOR 0.26,0.188 0.573,0.344 0.313,0.156 10 false D43 4.396,5.854 4.698,6.031 0.302,0.177 10 false A33 5.5,1.135 5.885,1.302 0.385,0.167 10 false DLC3 5.5,0.969 5.771,1.146 0.271,0.177 10 false D10 5.156,0.281 5.281,0.469 0.125,0.188 10 false 6 4.365,0.281 4.479,0.458 0.115,0.177 10 false 5 4.823,0.229 5.073,0.385 0.25,0.156 10 false B-Y 4.844,0.854 5.052,1.021 0.208,0.167 10 false LG 3.854,4.771 4,4.938 0.146,0.167 10 false 9 2.719,4.771 2.896,4.927 0.177,0.156 10 false 20 3.854,5.667 4.042,5.833 0.188,0.167 10 false 19 2.719,5.667 2.917,5.844 0.198,0.177 10 false 18 3.854,5.219 4,5.385 0.146,0.167 10 false O 2.656,5.24 2.906,5.396 0.25,0.156 10 false B-P 4.365,0.771 4.552,0.948 0.188,0.177 10 false 16 5.26,0.771 5.438,0.927 0.177,0.156 10 false 14 1.729,3.177 1.969,3.333 0.24,0.156 10 false P-L 1.729,3.896 2.031,4.063 0.302,0.167 10 false R-W 1.271,3.25 1.458,3.417 0.188,0.167 10 false 13 1.271,3.823 1.448,4 0.177,0.177 10 false 22 2.25,3.25 2.365,3.406 0.115,0.156 10 false 8 2.198,3.833 2.375,4.01 0.177,0.177 10 false 19 0.083,4.083 0.385,4.26 0.302,0.177 10 false D27 0.083,4.25 1.01,4.594 0.927,0.344 10 false AIR BAG ECU ASSEMBLY 1.688,1.125 1.99,1.281 0.302,0.156 10 false G-W 1.792,1.854 1.917,2.031 0.125,0.177 10 false G 1.271,1.177 1.406,1.344 0.135,0.167 10 false 3 1.271,1.781 1.385,1.958 0.115,0.177 10 false 2 2.24,1.177 2.365,1.354 0.125,0.177 10 false 6 2.219,1.781 2.385,1.958 0.167,0.177 10 false 17 0.042,2.042 0.344,2.198 0.302,0.156 10 false D56 0.042,2.208 2.271,2.573 2.229,0.365 10 false STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) 0.052,5.594 1.375,5.948 1.323,0.354 10 false *3 : for Automatic Air Conditioning System 0.094,5.219 1.333,5.406 1.24,0.188 10 false x : Suspected Area 5.5,2.667 5.802,2.844 0.302,0.177 10 false D29 4.844,1.729 4.958,1.906 0.115,0.177 10 false P 4.875,2.458 4.979,2.646 0.104,0.188 10 false L 4.396,1.802 4.521,1.969 0.125,0.167 10 false 7 4.365,2.427 4.542,2.604 0.177,0.177 10 false 18 5.365,1.802 5.479,1.969 0.115,0.167 10 false 4 5.365,2.417 5.479,2.594 0.115,0.177 10 false 5 5.5,2.844 6.448,3.188 0.948,0.344 10 false PSP (OPTION CONNECTOR) 5.313,4.708 5.604,4.875 0.292,0.167 10 false D19 4.802,3.792 5.094,3.948 0.292,0.156 10 false L-W 4.802,4.531 5.042,4.698 0.24,0.167 10 false L-Y 4.365,3.854 4.573,4.021 0.208,0.167 10 false 10 4.375,4.458 4.563,4.635 0.188,0.177 10 false 21 5.313,3.875 5.479,4.042 0.167,0.167 10 false 13 5.302,4.458 5.479,4.625 0.177,0.167 10 false 12 5.302,4.885 6.917,5.24 1.615,0.354 10 false AIR CONDITIONING CONTROL ASSEMBLY*3 3.188,6.479 3.604,6.646 0.417,0.167 10 false 120 Ω 0.635,6.844 2.438,7.031 1.802,0.188 10 false : CAN Main Bus Line (CANH) 0.635,7.219 2.427,7.406 1.792,0.188 10 false : CAN Main Bus Line (CANL) 3.469,6.906 5.417,7.083 1.948,0.177 10 false : CAN Branch Bus Line (CANH) 3.458,7.25 5.385,7.427 1.927,0.177 10 false : CAN Branch Bus Line (CANL) 0.781,1.198 1.198,1.354 0.417,0.156 10 false CANH 0.792,1.781 1.177,1.958 0.385,0.177 10 false CANL 5.552,1.802 5.979,1.969 0.427,0.167 10 false CANH 5.563,2.406 5.948,2.563 0.385,0.156 10 false CANL 5.542,3.885 5.969,4.042 0.427,0.156 10 false CANH 3.833,5.885 4.26,6.063 0.427,0.177 10 false CANH 5.552,4.448 5.948,4.615 0.396,0.167 10 false CANL 2.542,5.875 2.938,6.042 0.396,0.167 10 false CANL 5.5,0.406 5.927,0.583 0.427,0.177 10 false CANH 5.521,0.656 5.917,0.833 0.396,0.177 10 false CANL 0.792,3.25 1.188,3.406 0.396,0.156 10 false CANH 0.792,3.823 1.188,3.99 0.396,0.167 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 2 J/C)
a.
U190378E02
0.667,0.865 1.177,1.531 true 1.198,1.927 0.656,2.573 true 0.469,1.042 1.01,1.521 true 1.021,1.917 0.469,2.396 true 0.292,1.292 0.823,1.552 true 0.792,1.917 0.292,2.156 true 0.844,0.604 1.365,1.531 true 1.375,1.917 0.844,2.833 true 1.01,0.354 1.552,1.542 true 1.563,1.927 1.01,3.073 true 2.865,0.865 2.323,1.542 true 2.354,1.917 2.854,2.573 true 3.052,1.125 2.51,1.521 true 2.552,1.917 3.052,2.313 true 2.667,0.604 2.177,1.521 true 2.146,1.896 2.667,2.833 true 2.5,0.354 2,1.521 true 1.969,1.927 2.521,3.052 true 1.208,0.094 1.75,1.542 true 1.75,1.917 1.208,3.323 true 2.104,3.323 1.75,3.677 true 0.427,0.781 0.583,0.958 0.156,0.177 10 false *d 0.427,2.479 0.583,2.646 0.156,0.167 10 false *d 0.229,0.958 0.385,1.156 0.156,0.198 10 false *c 0.229,2.313 0.385,2.49 0.156,0.177 10 false *c 0.052,1.208 0.219,1.406 0.167,0.198 10 false *b 0.052,2.073 0.229,2.25 0.177,0.177 10 false *b 0.604,0.521 0.771,0.708 0.167,0.188 10 false *e 0.604,2.74 0.76,2.927 0.156,0.188 10 false *e 0.781,0.271 0.938,0.448 0.156,0.177 10 false *f 0.781,2.979 0.938,3.156 0.156,0.177 10 false *f 2.896,0.781 3.031,1 0.135,0.219 10 false *j 2.896,2.479 3.031,2.698 0.135,0.219 10 false *j 3.094,1.042 3.271,1.24 0.177,0.198 10 false *k 3.094,2.229 3.26,2.427 0.167,0.198 10 false *k 2.729,0.521 2.854,0.708 0.125,0.188 10 false *i 2.729,2.74 2.875,2.938 0.146,0.198 10 false *i 2.552,0.271 2.719,0.448 0.167,0.177 10 false *h 2.552,2.979 2.74,3.156 0.188,0.177 10 false *h 0.969,0.01 1.135,0.24 0.167,0.229 10 false *g 0.969,3.24 1.135,3.438 0.167,0.198 10 false *g 1.604,0.542 1.896,0.698 0.292,0.156 10 false D43 1.615,3.198 1.906,3.354 0.292,0.156 10 false D10 0.135,0.073 0.313,0.271 0.177,0.198 10 false *a 0.135,3.333 0.302,3.51 0.167,0.177 10 false *1 2.146,3.229 2.385,3.396 0.24,0.167 10 false CG

Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
D43-1 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher CAN No. 1 junction connector
D43-12 - D10-4 (CG)
D43-2 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
D43-13 - D10-4 (CG)
D43-3 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (network gateway ECU)
D43-14 - D10-4 (CG)
D43-4 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
D43-15 - D10-4 (CG)
D43-5 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher DLC3
D43-16 - D10-4 (CG)
D43-6 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering angle sensor (spiral cable sub-assembly)
D43-17 - D10-4 (CG)
D43-7 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher PSP (option connector)
D43-18 - D10-4 (CG)
D43-8 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air bag ECU assembly
D43-19 - D10-4 (CG)
D43-9 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
D43-20 - D10-4 (CG)
D43-10 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning control assembly
D43-21 - D10-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
*c to Combination Meter Assembly
*d to Main Body ECU (Network Gateway ECU)
*e to Certification ECU (Smart Key ECU Assembly)
*f to DLC3
*g to Steering Angle Sensor (Spiral Cable Sub-assembly)
*h to PSP (Option Connector)
*i to Air Bag ECU Assembly
*j to ECM
*k to Air Conditioning Control Assembly

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (ECM main line) C
NG (ECU or sensor branch line) D
NG (DLC3 branch line or PSP (option connector) branch line) E




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - ECM)

D

3.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)

E

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3 OR PSP (OPTION CONNECTOR)

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 J/C)
a.
U147163E01
2.151,3.227 2.446,3.383 0.295,0.156 10 CG 2.108,3.327 1.755,3.674 false 0.795,0.268 1.229,0.407 0.434,0.139 10 *b 0.795,2.983 1.234,3.122 0.439,0.139 10 *b 1.033,0.35 1.526,1.517 false 1.526,1.92 1.032,3.069 false 2.744,0.526 3.178,0.665 0.434,0.139 10 *e 2.744,2.742 3.183,2.881 0.439,0.139 10 *e 2.686,0.608 2.193,1.517 false 2.193,1.92 2.686,2.829 false 2.574,0.268 3.008,0.407 0.434,0.139 10 *d 2.574,2.983 3.013,3.122 0.439,0.139 10 *d 2.513,0.35 2.019,1.517 false 2.019,1.92 2.513,3.069 false 0.984,0.01 1.418,0.149 0.434,0.139 10 *c 0.984,3.241 1.423,3.380 0.439,0.139 10 *c 1.222,0.093 1.715,1.517 false 1.715,1.92 1.222,3.327 false 1.6,0.52 1.896,0.676 0.295,0.156 10 A17 1.6,3.189 1.896,3.346 0.295,0.156 10 D10 0.14,0.07 0.435,0.226 0.295,0.156 10 *a 0.14,3.331 0.435,3.487 0.295,0.156 10 *1

Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A17-5 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM
A17-16 - D10-4 (CG)
A17-6 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Skid control ECU (brake actuator assembly)
A17-17 - D10-4 (CG)
A17-7 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher CAN No. 2 junction connector
A17-18 - D10-4 (CG)
A17-8 - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
A17-19 - D10-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to TCM
*c to Skid Control ECU (Brake Actuator Assembly)
*d to CAN No. 2 Junction Connector
*e to Power Steering ECU Assembly


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (skid control ECU (brake actuator assembly) main line) C
NG (ECU or sensor branch line) D



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 1 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

D

3.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU, SENSOR)
a.

Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).



c.
U147251E03
1.25,0.365 1.552,0.906 true 2.302,0.375 2.01,0.906 true 1.896,1.49 1.604,2.031 true 1.479,0.333 1.75,0.49 0.271,0.156 10 false D10 0.083,0.063 0.375,0.219 0.292,0.156 10 false *1 1,0.271 1.24,0.427 0.24,0.156 10 false CG 2.385,0.229 2.802,0.385 0.417,0.156 10 false CANH 1.177,1.927 1.573,2.083 0.396,0.156 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-6 (CANH) - D10-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
D10-14 (CANL) - D10-4 (CG)


Text in Illustration
*1 DLC3


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE REPAIR OR REPLACE CORRESPONDING ECU/SENSOR WIRE OR CONNECTOR