Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297666 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)


U146879E03
0.385,1.198 0.583,1.354 0.198,0.156 10 false 3D 0.208,0.167 0.406,0.323 0.198,0.156 10 false *1 1.885,6.583 2.083,6.74 0.198,0.156 10 false *2 1.469,4.052 1.667,4.208 0.198,0.156 10 false 3D 3.75,1.073 3.979,1.229 0.229,0.156 10 false MB 3.51,3.24 3.74,3.396 0.229,0.156 10 false MB 6.344,1.156 6.531,1.313 0.188,0.156 10 false 3B 1.792,5.281 1.979,5.438 0.188,0.156 10 false 3B 6.354,1.813 6.542,1.969 0.188,0.156 10 false 3A 4.938,5.292 5.125,5.448 0.188,0.156 10 false 3A 0.385,1.771 0.583,1.927 0.198,0.156 10 false 3C 4.208,4.063 4.406,4.219 0.198,0.156 10 false 3C 0.385,2.396 0.573,2.552 0.188,0.156 10 false 3E 6.25,4.052 6.438,4.208 0.188,0.156 10 false 3E 3.042,6.552 3.313,6.708 0.271,0.156 10 false A73 1.125,7.49 1.396,7.646 0.271,0.156 10 false A73 3.719,6.542 3.917,6.698 0.198,0.156 10 false D5 3.594,7.5 3.792,7.656 0.198,0.156 10 false D5 4.24,6.542 4.438,6.698 0.198,0.156 10 false D6 5.917,7.49 6.115,7.646 0.198,0.156 10 false D6

Text in Illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Network Gateway ECU)

a.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Switch Condition Specified Condition
MB-1 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
MB-8 (IG) - Body ground None - Body ground Battery power supply Ignition switch ON 11 to 14 V
MB-11 (GND) - Body ground None - Body ground Ground Always Below 1 Ω
MB-32 (BMPX) - Body ground None - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (network gateway ECU) onto the instrument panel junction block assembly.


d.

Measure the pulses according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Switch Condition Specified Condition
D5-4 (LIN) - D6-1 (GND) LG - B LIN Communication line Ignition switch ON Pulse generation

If the result is not as specified, the main body ECU (network gateway ECU) or instrument panel junction block assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


U190429E02
2.896,0.135 3.094,0.302 0.198,0.167 10 false F6 3.75,0.135 3.958,0.302 0.208,0.167 10 false E8 3.229,0.135 3.406,0.302 0.177,0.167 10 false *1 4.094,0.135 4.26,0.302 0.167,0.167 10 false *2

Text in Illustration
*1 for RHD *2 for LHD

a.

Disconnect the F6*1 or E8*2 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
F6-5 (GND) - Body ground*1 B - Body ground Ground Always Below 1 Ω
E8-5 (GND) - Body ground*2
F6-12 (+B) - Body ground*1 SB - Body ground Battery power supply Always 11 to 14 V
E8-12 (+B) - Body ground*2

If the result is not as specified, there may be a malfunction in the wire harness.

*1 : for RHD

*2 : for LHD



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


U190182E02
4.854,0.771 5.115,0.938 0.26,0.167 10 false D41 1.938,0.771 2.198,0.927 0.26,0.156 10 false D48

a.

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Switch Condition Specified Condition
D48-2 (+B) - D48-11 (GND) R - B Battery power supply Always 11 to 14 V
D48-11 (GND) - Body ground B - Body ground Ground Always Below 1 Ω


c.

Connect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Switch Condition Specified Condition
D41-5 (IG2) - D48-11 (GND) Y - B Battery power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK STEERING LOCK ACTUATOR ASSEMBLY (w/ Entry and Start System)


U190179E02
3.313,0.177 3.594,0.333 0.281,0.156 10 false D59

a.

Disconnect the D59 steering lock actuator assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Switch Condition Specified Condition
D59-1 (GND) - Body ground B - Body ground Ground Always Below 1 Ω
D59-6 (IGN1) - D59-1 (GND) BR - B Battery power supply Ignition switch ON 11 to 14 V
D59-7 (B) - D59-1 (GND) SB - B Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ Entry and Start System with ID Code Box)


U190439E02
3.615,0.24 3.906,0.396 0.292,0.156 10 false A30

a.

Disconnect the A30 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No.
(Symbol)
Wiring Color Terminal Description Condition Specified Condition
A30-1 (+B) - A30-5 (GND) R-W - B-Y Battery power supply Always 11 to 14 V
A30-5 (GND) - Body ground B-Y - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.