Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297666 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors the communications with the steering lock actuator assembly connected to the certification LIN bus and the ID code box (immobiliser code ECU)*. DTC B2785 is stored if the certification ECU (smart key ECU assembly) detects a communications error between the steering lock actuator assembly connected to the certification LIN bus and the ID code box (immobiliser code ECU), and the LIN communications error (+B short, GND short, communication not possible because of noise, etc.) continues for 1 second.

DTC No. DTC Detection Condition Trouble Area
B2785 The certification ECU (smart key ECU assembly) detects a LIN communication error (+B short, GND short, communication not possible because of noise, etc.) that continues for 1 second.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator assembly

·

ID code box (immobiliser code ECU)*

·

Harness or connector



* : w/ ID Code Box

WIRING DIAGRAM

E201074E27
0.76,1.813 2.625,2.156 1.865,0.344 10 false STEERING LOCK ACTUATOR ASSEMBLY 4.719,1.802 6.646,2.177 1.927,0.375 10 false CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 2.677,3.865 4.552,4.219 1.875,0.354 10 false ID CODE BOX (IMMOBILISER CODE ECU)* 0.667,4.396 2.26,4.583 1.594,0.188 10 false : LIN Communication Line 2.229,1.052 2.458,1.198 0.229,0.146 10 false LIN 4.781,1.021 5.031,1.188 0.25,0.167 10 false LIN 3.479,2.792 3.708,2.958 0.229,0.167 10 false LIN 4.51,0.885 4.677,1.042 0.167,0.156 10 false 17 2.552,0.885 2.74,1.042 0.188,0.156 10 false 5 3.667,2.542 3.792,2.708 0.125,0.167 10 false 2 0.76,1.625 1.042,1.802 0.281,0.177 10 false D59 4.729,1.625 4.99,1.781 0.26,0.156 10 false D41 2.677,3.698 2.948,3.865 0.271,0.167 10 false A30 2.5,4.385 3.688,4.563 1.188,0.177 10 false * : w/ ID Code Box

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ID code box (immobiliser code ECU)*, certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the registration procedures for the Service Bulletin.

·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.


* : w/ ID Code Box


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC 2785 is output A
DTC 2785 is not output B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D59 steering lock actuator assembly connector.


c.

Disconnect the A30 ID code box (immobiliser code ECU)* connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D41-17 (LIN) - D59-5 (LIN) Always Below 1 Ω
D41-17 (LIN) - A30-2 (LIN)* Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D41-17 (LIN) or D59-5 (LIN) - Body ground Always 10 kΩ or higher
D41-17 (LIN) or A30-2 (LIN) - Body ground* Always 10 kΩ or higher



e.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


f.

Reconnect the D59 steering lock actuator assembly connector.


* : w/ ID Code Box


OK

4.SYSTEM CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.SYSTEM CHECK
a.

Check the vehicle specifications.


Result
Result Proceed to
w/ ID Code Box A
w/o ID Code Box B


A

5.CLEAR DTC

B

7.CLEAR DTC
5.CLEAR DTC

NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

7.CLEAR DTC

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

7.CLEAR DTC
a.

Disconnect the D59 steering lock actuator assembly connector.




NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY