Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) › from 2014.05
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297668 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

w/o Tire Pressure Warning System

This door control receiver receives signals from the transmitter and sends these signals to the main body ECU (network gateway ECU).


w/ Tire Pressure Warning System

The door control receiver receives signals from the door control transmitter and sends these signals to the main body ECU (network gateway ECU) via the tire pressure warning ECU and receiver.


DTC No. DTC Detection Condition Trouble Area
B1242 In diagnostic mode, applicable RDA signal cannot be received 3 times in succession after the PRG signal is output from the main body ECU (network gateway ECU).
·

Wire harness or connector

·

Door control receiver

·

Main body ECU (network gateway ECU)

·

Tire pressure warning ECU and receiver*



*: w/ Tire Pressure Warning System


WIRING DIAGRAM

B374184E02
5.458,2.042 7.156,2.677 1.698,0.635 10 false Main Body ECU (Network Gateway ECU) 0.281,2.448 1.781,2.75 1.5,0.302 10 false Door Control Receiver 0.281,2.281 0.604,2.458 0.323,0.177 10 false H27 5.458,1.865 5.781,2.042 0.323,0.177 10 false D6 0.052,0.042 2.99,0.438 2.938,0.396 12 false w/o Tire Pressure Warning System: 1.063,1.979 1.448,2.156 0.385,0.177 10 false GND 1.479,1.885 1.625,2.063 0.146,0.177 10 false 1 1.063,1.51 1.448,1.688 0.385,0.177 10 false PRG 1.479,1.438 1.625,1.615 0.146,0.177 10 false 3 5.875,1.521 6.26,1.698 0.385,0.177 10 false PRG 5.646,1.438 5.844,1.615 0.198,0.177 10 false 6 5.875,1.042 6.26,1.219 0.385,0.177 10 false RDA 1.063,1.042 1.448,1.219 0.385,0.177 10 false RDA 1.479,0.948 1.625,1.125 0.146,0.177 10 false 2 1.188,0.583 1.458,0.76 0.271,0.177 10 false +B 1.479,0.5 1.625,0.677 0.146,0.177 10 false 5 5.646,0.948 5.844,1.125 0.198,0.177 10 false 7 4.688,0.594 5.5,0.896 0.813,0.302 10 false from Battery 2.167,0.74 2.677,0.906 0.51,0.167 10 false ECU-B

B374185E02
5.458,2.99 7.156,3.625 1.698,0.635 10 false Main Body ECU (Network Gateway ECU) 0.281,3.417 1.781,3.719 1.5,0.302 10 false Door Control Receiver 0.281,3.25 0.604,3.427 0.323,0.177 10 false H27 2.406,3.104 3.885,3.76 1.479,0.656 10 false Tire Pressure Warning ECU and Receiver 2.406,2.927 2.729,3.104 0.323,0.177 10 false H28 4.677,0.563 5.49,0.865 0.813,0.302 10 false from Battery 1.938,0.729 2.448,0.896 0.51,0.167 10 false ECU-B 5.458,2.813 5.781,2.99 0.323,0.177 10 false D6 0.073,0.073 2.698,0.469 2.625,0.396 12 false w/ Tire Pressure Warning System: 1.063,2.938 1.448,3.115 0.385,0.177 10 false GND 1.479,2.833 1.625,3.01 0.146,0.177 10 false 1 1.063,2.094 1.448,2.271 0.385,0.177 10 false PRG 2.344,1.979 2.49,2.156 0.146,0.177 10 false 9 3.667,1.479 3.813,1.656 0.146,0.177 10 false 7 3.656,1.01 3.802,1.188 0.146,0.177 10 false 1 3.667,2.427 3.813,2.604 0.146,0.177 10 false 5 3.667,2 3.813,2.177 0.146,0.177 10 false 4 1.479,1.99 1.625,2.167 0.146,0.177 10 false 3 2.531,2.531 2.906,2.708 0.375,0.177 10 false GND 3.177,2.531 3.625,2.708 0.448,0.177 10 false BPRG 3.365,1.573 3.583,1.75 0.219,0.177 10 false +B 3.375,1.104 3.594,1.281 0.219,0.177 10 false IG 3.177,2.073 3.625,2.25 0.448,0.177 10 false BRDA 2.531,2.073 2.979,2.25 0.448,0.177 10 false RPRG 2.531,1.51 2.979,1.688 0.448,0.177 10 false RRDA 5.823,2.521 6.208,2.698 0.385,0.177 10 false PRG 5.604,2.427 5.802,2.604 0.198,0.177 10 false 6 5.823,2.083 6.208,2.26 0.385,0.177 10 false RDA 1.063,1.51 1.448,1.688 0.385,0.177 10 false RDA 1.479,1.417 1.625,1.594 0.146,0.177 10 false 2 1.188,0.573 1.458,0.75 0.271,0.177 10 false +B 1.479,0.469 1.625,0.646 0.146,0.177 10 false 5 5.604,1.99 5.802,2.167 0.198,0.177 10 false 7 2.292,1.417 2.49,1.594 0.198,0.177 10 false 10 2.271,2.417 2.469,2.594 0.198,0.177 10 false 12 5,1.573 5.813,1.875 0.813,0.302 10 false from Battery 4.979,1.104 6.438,1.406 1.458,0.302 10 false from IG1 NO. 1 Relay 3.979,1.26 4.594,1.427 0.615,0.167 10 false ECU IG1 4.031,1.729 4.542,1.896 0.51,0.167 10 false MPX-B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

* When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

* It is necessary to perform initialization after registration of the transmitter IDs into the tire pressure warning ECU and receiver if the tire pressure warning ECU and receiver has been replaced.




*: w/ Tire Pressure Warning System


PROCEDURE

1.CONFIRM VEHICLE SPECIFICATION
a.

Confirm the vehicle specification.


Result
Result Proceed to
w/ Tire Pressure Warning System A
w/o Tire Pressure Warning System B


A

2.CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - DOOR CONTROL RECEIVER)
2.CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)


OK:

DTCs are not output.


Result
Result Proceed to
NG A
OK B


A

B

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - DOOR CONTROL RECEIVER)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Disconnect the H27 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D6-6 (PRG) - H27-3 (PRG) Always Below 1 Ω
D6-7 (RDA) - H27-2 (RDA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D6-6 (PRG) or H27-3 (PRG) - Body ground Always 10 kΩ or higher
D6-7 (RDA) or H27-2 (RDA) - Body ground Always 10 kΩ or higher




OK

4.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)
a.
U190178E01
0.205,0.157 0.391,0.318 0.186,0.161 10 *a 1.522,0.236 1.817,0.392 0.295,0.156 10 H27 2.137,1.489 2.268,1.907 false 2.186,1.919 2.407,2.075 0.221,0.156 10 +B 1.295,1.489 1.164,1.907 false 0.944,1.919 1.283,2.075 0.340,0.156 10 GND

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H27-5 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H27-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

5.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOOR CONTROL RECEIVER
a.

Replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).



NEXT

6.REGISTER RECOGNITION CODE
6.REGISTER RECOGNITION CODE

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Disconnect the H28 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D6-7 (RDA) - H28-4 (BRDA) Always Below 1 Ω
D6-6 (PRG) - H28-5 (BPRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D6-7 (RDA) or H28-4 (BRDA) - Body ground Always 10 kΩ or higher
D6-6 (PRG) or H28-5 (BPRG) - Body ground Always 10 kΩ or higher



OK

9.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector.


b.

Disconnect the H27 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
H28-10 (RRDA) - H27-2 (RDA) Always Below 1 Ω
H28-9 (RPRG) - H27-3 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
H28-10 (RRDA) or H27-2 (RDA) - Body ground Always 10 kΩ or higher
H28-9 (RPRG) or H27-3 (PRG) - Body ground Always 10 kΩ or higher



OK

10.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)
a.
U190178E01
0.205,0.157 0.391,0.318 0.186,0.161 10 *a 1.522,0.236 1.817,0.392 0.295,0.156 10 H27 2.137,1.489 2.268,1.907 false 2.186,1.919 2.407,2.075 0.221,0.156 10 +B 1.295,1.489 1.164,1.907 false 0.944,1.919 1.283,2.075 0.340,0.156 10 GND

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H27-5 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H27-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

11.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (POWER SOURCE, GROUND)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.


U190295E02
1.302,1.625 1.167,1.969 1.167,1.969 1.031,1.969 true 2.208,1.625 2.344,1.969 2.344,1.969 2.49,1.969 true 1.292,1.281 1.146,0.938 1.146,0.938 0.885,0.938 true 1.625,0.208 1.917,0.365 0.292,0.156 10 false H28 0.115,0.052 0.302,0.208 0.188,0.156 10 false *a 2.552,1.885 2.927,2.063 0.375,0.177 10 false GND 0.667,0.854 0.875,1.031 0.208,0.177 10 false IG 0.75,1.896 0.979,2.073 0.229,0.177 10 false +B

Standard Voltage:
Tester Connection Condition Specified Condition
H28-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H28-7 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H28-12 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

12.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE DOOR CONTROL RECEIVER
a.

Replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).



NEXT

13.REGISTER RECOGNITION CODE
13.REGISTER RECOGNITION CODE

NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC

OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

15.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
15.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver with a new one (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC

OK

END (TIRE PRESSURE WARNING ECU AND RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)