Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297668 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (network gateway ECU) may be malfunctioning.

WIRING DIAGRAM

B315516E05
3.26,2.198 4.917,2.844 1.656,0.646 10 false Main Body ECU (Network Gateway ECU) 2.302,3.094 4.979,3.396 2.677,0.302 10 false Instrument Panel Junction Block Assembly 2.313,2.896 2.521,3.052 0.208,0.156 10 false 3B 4.979,1.125 5.26,1.271 0.281,0.146 10 false A73 3.635,0.656 3.906,0.813 0.271,0.156 10 false MB 5.073,0.906 5.198,1.083 0.125,0.177 10 false 1 2.323,2.146 2.51,2.292 0.188,0.146 10 false 16 2.323,0.563 2.51,0.708 0.188,0.146 10 false 14 3.708,0.469 3.813,0.625 0.104,0.156 10 false 3 1.854,0.573 1.958,0.729 0.104,0.156 10 false 7 1.844,2.135 1.948,2.292 0.104,0.156 10 false 8 0.542,0.854 0.729,1.01 0.188,0.156 10 false 14 0.5,1.135 0.802,1.292 0.302,0.156 10 false D18 0.656,2.615 0.948,2.781 0.292,0.167 10 false D61 0.594,0.271 0.698,0.427 0.104,0.156 10 false 8 6.49,1.104 6.615,1.281 0.125,0.177 10 false - 5.781,1.094 5.906,1.271 0.125,0.177 10 false + 5.594,0.99 5.719,1.167 0.125,0.177 10 false 1 6.646,1 6.771,1.177 0.125,0.177 10 false 2 5.323,1.469 5.604,1.625 0.281,0.156 10 false A63 5.323,1.635 7.052,1.948 1.729,0.313 10 false Wireless Door Lock Buzzer 0.656,2.802 1.917,3.448 1.26,0.646 10 false Turn Signal Flasher Assembly 0.49,1.302 2.104,1.948 1.615,0.646 10 false Clock Assembly (Hazard Warning Signal Switch) 0.76,0.385 1.104,0.552 0.344,0.167 10 false GND 3.979,0.646 4.313,0.813 0.333,0.167 10 false HZR 1.125,0.656 1.813,0.823 0.688,0.167 10 false HAZARD+ 0.76,0.917 1.448,1.083 0.688,0.167 10 false HAZARD- 1.438,2.25 1.813,2.417 0.375,0.167 10 false EHW 4.594,1.135 4.927,1.302 0.333,0.167 10 false BZR 0.104,3.375 4.125,3.625 4.021,0.25 10 false *: w/ Wireless Door Lock Buzzer Answer-back Function 5.406,1.083 5.594,1.229 0.188,0.146 10 false *

PROCEDURE

1.READ VALUE USING GTS (ANSWER-BACK OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Utility / Customize / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Display Default Content Setting Relevant ECU
Hazard Answer Back ON When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
OFF or ON Main body ECU (network gateway ECU)
Wireless Buzzer Resp* ON Wireless door lock buzzer response OFF or ON Main body ECU (network gateway ECU)
Wireless Buzzer Vol* Level 5 Wireless door lock buzzer volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0 Main body ECU (network gateway ECU)

*: w/ Wireless Door Lock Buzzer Answer-back Function


Result:
Result Proceed to
Both items are ON and except Level 0 A
Either item is OFF or Level 0 B




A

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the door control transmitter module set sub-assembly.

Result:
Result Proceed to
Wireless door lock/unlock operates normally (w/ Wireless Door Lock Buzzer Answer-back Function). A
Wireless door lock/unlock operates normally (w/o Wireless Door Lock Buzzer Answer-back Function). B
Wireless door lock/unlock does not operate normally. C




A

3.CHECK WIRELESS ANSWER-BACK OPERATION

B

8.HAZARD WARNING LIGHTS OPERATION

C

3.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the door control transmitter module set sub-assembly.

Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. A
Only hazard warning light answer-back does not occur. B




A

4.PERFORM ACTIVE TEST USING GTS (WIRELESS DOOR LOCK BUZZER)

B

8.HAZARD WARNING LIGHTS OPERATION
4.PERFORM ACTIVE TEST USING GTS (WIRELESS DOOR LOCK BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Wireless Buzzer Turns the wireless door lock buzzer ON/OFF -

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off. A
Wireless door lock buzzer turns on/off. B




A

5.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU)

B

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

5.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU)
a.

Disconnect the A63 wireless door lock buzzer connector.


b.

Disconnect the A73 main body ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-1 (+) - A73-1 (BZR) Always Below 1 Ω
A63-2 (-) - Body ground Always Below 1 Ω
A63-1 (+) - Body ground Always 10 kΩ or higher




OK

6.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL).



NEXT

7.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
7.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

OK:

Wireless answer-back function operates normally.




OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

8.HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normally.




OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U146891E01
0.114,0.061 0.300,0.222 0.186,0.161 10 *a 2.219,0.427 2.462,0.583 0.243,0.156 10 MB 5.651,0.22 5.869,0.376 0.218,0.156 10 3B 0.961,0.94 0.902,1.175 false 0.751,1.19 1.087,1.346 0.335,0.156 10 HZR

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-14 - MB-3 (HZR) Always Below 1 Ω
3B-16 - MB-3 (HZR) Always Below 1 Ω



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY