Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297670 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive electrical waves relating to the entry functions of the entry and start system. The certification ECU (smart key ECU assembly) decodes the requested entry and start system operation by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU).

DTC No. DTC Detection Condition Trouble Area
B1242
·

Short in RDA or RSSI to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RDA or RSSI to ground when RC0 (12 V) output from the ECU is off.


·

Door control receiver

·

Wire harness or connector

·

Certification ECU (Smart Key ECU Assembly)



WIRING DIAGRAM

B265620E71
4.875,2.229 5.177,2.427 0.302,0.198 10 false D48 0.76,2.927 2.156,3.115 1.396,0.188 10 false Door Control Receiver 0.76,2.75 1.042,2.906 0.281,0.156 10 false H26 5.052,2.771 6.625,3.125 1.573,0.354 10 false Certification ECU (Smart Key ECU Assembly) 4.875,1.646 5.177,1.844 0.302,0.198 10 false D40 4.875,1.156 5.177,1.354 0.302,0.198 10 false D40 4.875,0.677 5.177,0.875 0.302,0.198 10 false D40 4.906,2 5.094,2.177 0.188,0.177 10 false 11 4.917,1.438 5.104,1.615 0.188,0.177 10 false 19 4.927,0.938 5.115,1.115 0.188,0.177 10 false 17 2.177,2.073 2.323,2.25 0.146,0.177 10 false 1 2.177,1.5 2.323,1.677 0.146,0.177 10 false 2 2.177,1.021 2.323,1.198 0.146,0.177 10 false 5 2.177,0.531 2.323,0.708 0.146,0.177 10 false 4 4.979,0.469 5.125,0.646 0.146,0.177 10 false 5 5.26,0.667 5.708,0.823 0.448,0.156 10 false RCO 5.25,1.146 5.677,1.302 0.427,0.156 10 false RDA 5.25,1.635 5.635,1.792 0.385,0.156 10 false RSSI 5.26,2.219 5.625,2.375 0.365,0.156 10 false GND 1.896,0.615 2.135,0.771 0.24,0.156 10 false +5 1.719,1.104 2.146,1.26 0.427,0.156 10 false DATA 1.75,1.604 2.135,1.76 0.385,0.156 10 false RSSI 1.771,2.177 2.135,2.333 0.365,0.156 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page ).

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.



PROCEDURE

1.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
U190211E01
1.565,0.232 1.897,0.413 0.332,0.181 10 H26 0.197,0.113 0.572,0.432 0.375,0.319 10 *a 2.079,1.292 2.427,1.812 false 2.253,1.818 2.665,1.975 0.412,0.157 10 DATA 1.896,1.292 2.021,1.812 false 1.57,1.292 1.522,1.812 false 1.398,1.292 0.972,1.812 false 0.743,1.824 1.118,1.981 0.375,0.157 10 GND 1.323,1.813 1.723,1.970 0.400,0.157 10 RSSI 1.942,1.818 2.162,1.975 0.221,0.157 10 +5

a.

Disconnect the H26 door control receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H26-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
H26-4 (+5) - H26-1 (GND) Always Below 1 V → 4.5 to 5.5 V (Pulse generation)
H26-2 (RSSI) - H26-1 (GND) Always 11 to 14 V
H26-5 (DATA) - H26-1 (GND) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)

Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU))

B

REPLACE DOOR CONTROL RECEIVER

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU))
a.

Disconnect the D40 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-19 (RSSI) - H26-2 (RSSI) Always Below 1 Ω
D40-17 (RDA) - H26-5 (DATA) Always Below 1 Ω
D40-5 (RCO) - H26-4 (+5) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR