Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

WIRING DIAGRAM

B312717E04
1.583,1.625 1.875,1.771 0.292,0.146 10 false GND 1.979,1.521 2.156,1.708 0.177,0.188 10 false 2 5.167,1.833 6.729,2.188 1.563,0.354 10 false Certification ECU (Smart Key ECU Assembly) 0.5,2.167 2.802,2.531 2.302,0.365 10 false Front Door Outside Handle Assembly (for Passenger Side Door) 5.448,0.885 5.823,1.094 0.375,0.208 10 false CG2B 5.448,0.5 5.823,0.656 0.375,0.156 10 false CLG2 5.448,1.25 5.823,1.417 0.375,0.167 10 false POS2 1.76,1.26 1.865,1.406 0.104,0.146 10 false B 1.521,0.896 1.938,1.063 0.417,0.167 10 false ANT2 1.521,0.521 1.885,0.677 0.365,0.156 10 false ANT1 5.188,1.146 5.365,1.333 0.177,0.188 10 false 21 5.188,0.781 5.365,0.969 0.177,0.188 10 false 10 5.177,0.417 5.354,0.604 0.177,0.188 10 false 11 1.979,0.417 2.156,0.604 0.177,0.188 10 false 6 1.979,0.781 2.156,0.969 0.177,0.188 10 false 3 1.979,1.146 2.156,1.333 0.177,0.188 10 false 5 5.177,1.667 5.5,1.823 0.323,0.156 10 false D41 0.51,2 0.854,2.156 0.344,0.156 10 false F5*1 0.854,2 1.198,2.156 0.344,0.156 10 false E1*2 3.021,2.271 3.719,2.438 0.698,0.167 10 false *1: for LHD 3.813,2.271 4.542,2.438 0.729,0.167 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.CHECK WAVE ENVIRONMENT

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE)

2.CHECK WAVE ENVIRONMENT
a.
B315532E01
1.167,1.34 1.339,1.500 0.171,0.160 10 *a 0.105,0.034 0.366,0.224 0.261,0.189 12 *A: 0.105,2.405 0.390,2.605 0.285,0.199 12 *B: 2.35,3.626 2.521,3.785 0.171,0.160 10 *a

Bring the electrical key transmitter sub-assembly near the front door outside handle assembly, and perform a front passenger door entry lock and unlock operation check.

Text in Illustration
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.98 ft.)

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.


HINT:
·

When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result
Result Proceed to
Entry functions operate abnormally A
Entry functions operate normally B



A

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F5*1 or E1*2 front door outside handle assembly (for passenger side door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
D41-11 (CLG2) - F5-6 (ANT1) Always Below 1 Ω
D41-10 (CG2B) - F5-3 (ANT2) Always Below 1 Ω
D41-21 (POS2) - F5-5 (B) Always Below 1 Ω
D41-11 (CLG2) - Body ground Always 10 kΩ or higher
D41-10 (CG2B) - Body ground Always 10 kΩ or higher
D41-21 (POS2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
D41-11 (CLG2) - E1-6 (ANT1) Always Below 1 Ω
D41-10 (CG2B) - E1-3 (ANT2) Always Below 1 Ω
D41-21 (POS2) - E1-5 (B) Always Below 1 Ω
D41-11 (CLG2) - Body ground Always 10 kΩ or higher
D41-10 (CG2B) - Body ground Always 10 kΩ or higher
D41-21 (POS2) - Body ground Always 10 kΩ or higher




OK

4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONTPASSENGER DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONTPASSENGER DOOR ELECTRICAL KEY ANTENNA)
a.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


b.
U190200E02
1.885,1.302 2.438,1.146 true 1.896,1.469 2.438,1.583 true 1.708,1.51 1.885,1.948 true 1.719,1.24 2.031,0.573 true 0.75,1.51 0.938,1.667 0.188,0.156 10 false *B 0.75,1.042 0.938,1.198 0.188,0.156 10 false *A 0.208,2.25 0.396,2.406 0.188,0.156 10 false *b 0.208,0.156 0.396,0.313 0.188,0.156 10 false *a 0.344,1.5 0.542,1.656 0.198,0.156 10 false E1 0.344,1.042 0.563,1.198 0.219,0.156 10 false F5 0.177,3.302 0.521,3.458 0.344,0.156 10 false GND 2.5,1.531 2.938,1.688 0.438,0.156 10 false ANT1 2.479,1.083 2.917,1.24 0.438,0.156 10 false ANT2 1.885,1.99 2.073,2.146 0.188,0.156 10 false B 2.042,0.396 2.406,0.552 0.365,0.156 10 false GND

Using an oscilloscope, check the waveform.

Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Door Outside Handle assembly)
*b Waveform

OK:
Tester Connection Condition Tool Setting Specified Condition
F5-6 (ANT1) - F5-3 (ANT2)*1
E1-6 (ANT1) - E1-3 (ANT2)*2
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*3

6.

All doors locked through wireless operation


5 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)


*1: for LHD

*2: for RHD

*3: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).




OK

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)
a.

Temporarily replace the front door outside handle assembly (for front passenger side door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR) (OPERATION)
6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR) (OPERATION)
a.

Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry functions operate normally.




OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)