Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2090E _59 Vehicle Exterior _060708 DOOR / HATCH _0297771 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for both the RH and LH sides.


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 74222 2.REMOVE DOOR ARMREST COVER

a.
B313118E01
2.258,3.603 2.409,3.757 0.152,0.154 10 *1 1.501,3.183 2.208,3.677 false

Using a screwdriver with its tip wrapped in protective tape, disengage the 7 claws.


b.

Disengage the guides and remove the door armrest cover.

Text in Illustration
*1 Protective Tape


Hide 81230 3.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 67602 4.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B313119E01
1.014,1.275 1.165,1.424 0.150,0.149 10 *1 1.329,0.695 1.153,1.24 false

Using a screwdriver with its tip wrapped in protective tape, open the cap.

Text in Illustration
*1 Protective Tape


b.
B313120

Using a clip remover, disengage the clip.


c.

Remove the 3 screws.


d.
B313121

Using a moulding remover, disengage the 10 clips.


e.

Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.


f.

Disconnect each connector.


g.

Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door glass weatherstrip inner.


h.
B313122E01
2.408,0.084 2.562,0.234 0.154,0.150 10 *1 0.19,1.791 0.345,1.941 0.154,0.150 10 *2 0.962,0.644 2.358,0.223 false 0.811,1.338 0.357,1.767 false

Disconnect the front door lock remote control cable and the front door inside locking cable.

Text in Illustration
*1 Front Door Inside Locking Cable
*2 Front Door Lock Remote Control Cable


Hide 69206B 5.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
U190260E01
1.52,0.509 1.521,0.45 1.521,0.45 1.58,0.451 false 1.813,0.513 1.814,0.454 1.814,0.454 1.755,0.453 false 1.622,0.451 1.711,0.452 false 1.52,0.557 1.519,0.616 1.519,0.616 1.578,0.617 false 1.812,0.561 1.812,0.621 1.812,0.621 1.752,0.62 false 1.619,0.618 1.708,0.619 false 2.776,0.46 2.777,0.401 2.777,0.401 2.836,0.402 false 3.069,0.464 3.07,0.405 3.07,0.405 3.01,0.404 false 2.877,0.402 2.966,0.404 false 2.775,0.508 2.774,0.567 2.774,0.567 2.834,0.568 false 3.068,0.512 3.067,0.572 3.067,0.572 3.008,0.571 false 2.875,0.569 2.964,0.57 false

Remove the 2 screws.


b.

Disengage the 2 guides and remove the front door inside handle sub-assembly.


Hide 6.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B314154

Remove the 4 screws and power window regulator master switch assembly with the front door armrest base panel.


Hide 7.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B314155

Remove the 4 screws and power window regulator switch assembly with front door armrest base panel.


Hide 74640C 8.REMOVE DOOR ASSIST GRIP ASSEMBLY

a.
B314156

Remove the 2 screws.


b.

Disengage the guide and remove the door assist grip assembly.


Hide 67736 9.REMOVE FRONT LOWER DOOR TRIM PAD

a.
B314157

Remove the front lower door trim pad with the 5 screws.


Hide 68172A 10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

a.

Put a 4 mm (0.1575 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.1969 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.1575 in.) drill bit to prevent the drill bit from going too deep.


B314158E01
4.952,0.295 5.105,0.442 0.153,0.147 10 a 6.456,0.642 6.609,0.790 0.153,0.147 10 *1 6.248,1.081 6.49,0.772 false 5.225,0.261 5.378,0.408 0.153,0.147 10 *2 5.121,0.605 5.269,0.417 false

Text in Illustration
*1 Drill *2 Tape
a 5.0 mm (0.1969 in.) - -


c.

Lightly press the drill against the 6 rivets and drill off the flanges of the 6 rivets.

CAUTION:

Take care with the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.
B314159

Disengage the 9 claws and remove the front door glass inner weatherstrip from the front door trim board sub-assembly, as shown in the illustration.


Hide 67835 11.REMOVE FRONT DOOR SPEAKER HOLE COVER (w/o Front Speaker)

a.
B309247

Remove the front door speaker hole cover with the 3 screws.


Hide 86160 12.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY (w/ Front Speaker)

Hide 67832 13.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B314956

Disconnect the outer rear view mirror sub-assembly connector.


b.
B314160

Disconnect the front door lock assembly connector.


c.

Remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 87906B 14.REMOVE OUTER REAR VIEW MIRROR SUB-ASSEMBLY

Hide 68102 15.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

B314161

a.

Provisionally install the power window regulator master switch (for driver side).


b.

Provisionally install the power window regulator switch (for passenger side).


c.

Connect the cable to the negative (-) battery terminal.


d.

Move the front door glass sub-assembly until the 2 nuts can be seen through the service holes.


e.

Disconnect the power window regulator master switch connector (for driver side).


f.

Disconnect the power window regulator switch connector (for passenger side).


g.

Disconnect the cable from the negative (-) battery terminal.


h.
B314162

Remove the 3 nuts.


i.

Shift the front door rear lower frame sub-assembly to the lower side of the door frame.


j.
B386125E03
0.583,2.906 0.76,3.094 0.177,0.188 2.115,0.406 2.01,0.281 false 2.5,0.656 2.635,0.469 false 2.49,1.125 2.635,1.104 false 2.208,1.083 1.979,1.083 false 2.021,0.615 1.813,0.594 false 1.365,3.74 1.177,3.927 true 1.031,1.25 1.563,2.188 true 1.031,3.917 1.198,4.083 0.167,0.167 10 false *a 1.688,0.177 1.99,0.344 0.302,0.167 10 false SST 0.688,1.146 0.99,1.313 0.302,0.167 10 false SST 0.927,2.021 1.094,2.188 0.167,0.167 10 true *1 2.708,1.563 2.875,1.729 0.167,0.167 10 true *2 0.583,2.906 0.75,3.073 0.167,0.167 10 false *3 2.646,1.01 2.813,1.177 0.167,0.167 10 false *4 1.813,0.99 1.979,1.156 0.167,0.167 10 false *5 1.625,0.51 1.792,0.677 0.167,0.167 10 false *2 2.646,0.375 2.813,0.542 0.167,0.167 10 false *6

Install SST as shown in the illustration.

Text in Illustration
*1 Door Glass Inner Stabilizer Bolt
*2 Nut A
*3 Nut B
*4 Front Door Glass Sub-assembly
*5 Front Door Window Regulator Sub-assembly
*6 Bolt
*a SST Number

SST
09801-18010  

HINT:

The SST number on SST must be visible.



k.

Secure the bolt using SST, and then remove nut A.


l.

Remove nut B from the front door glass sub-assembly.


m.

Loosen the door glass inner stabilizer bolt.

NOTICE:

After the 2 nuts are removed, do not allow the door glass to fall.



n.
B314795

While holding the front door glass sub-assembly up, slide the front door rear lower frame sub-assembly downward, and pull the front door glass sub-assembly out from the front door rear lower frame sub-assembly.

NOTICE:
·

Do not allow the door glass to fall.

·

Do not damage the door glass.




o.

Partially remove the rear end of the front door weatherstrip until the front door glass sub-assembly can be removed.


p.
B314796

Remove the front door glass sub-assembly from the position indicated in the illustration.

NOTICE:

Do not damage the front door weatherstrip.


HINT:

The front glass sub-assembly can only be removed from the position indicated in the illustration.



Hide 67404F 16.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.

Remove the front door rear lower frame sub-assembly from the front door frame.


Hide 67241A 17.REMOVE DOOR GLASS INNER STABILIZER

a.

Remove the bolt and the door glass inner stabilizer.


Hide 67402F 18.REMOVE FRONT DOOR SUSH

a.
B314797

Remove the 3 nuts.


b.
B314798E01
2.072,0.615 2.272,0.792 0.201,0.177 10 (1) 0.72,1.52 0.921,1.697 0.201,0.177 10 (2)

Rotate the front door sush as indicated by the arrows in the order shown in the illustration, and remove the front door sush.

NOTICE:
·

Since the front door sush attachment bolts interfere, be sure to follow the procedure shown in the illustration.

·

Do not allow the front door sush to fall.

·

Do not damage the front door sush.




Hide 62616 19.REMOVE FRONT DOOR SASH STOPPER

a.

Remove the nut and front door sush stopper.


Hide 69802 20.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.
B314800E01
1.101,0.569 1.251,0.725 0.150,0.156 10 *1 1.284,0.683 1.999,0.891 false

Disconnect the connector.


b.

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly may fall and cause damage.



c.

Remove the 3 bolts and 2 nuts.


d.

Remove the temporary bolt and the front door window regulator sub-assembly with power window regulator motor assembly.


Hide 85720D 21.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

Hide 67862 22.REMOVE FRONT DOOR WEATHERSTRIP

a.

Disengage the 2 claws and remove the screw.


b.

Using a clip remover, disengage the 16 clips and remove the front door weatherstrip.

B314801


Hide 69510 23.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B228716

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly with front door outside handle cover LH.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217F 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B228718

Using a screwdriver, disengage the claw and 2 guides and remove the front door outside handle cover, as shown in the illustration.


Hide 69217E 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B314803

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69320 26.REMOVE FRONT DOOR LOCK ASSEMBLY

Hide 69220 27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Entry and Start System)

a.
B314804

Remove the front door outside handle assembly, as shown in the illustration.


Hide 69220 28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Entry and Start System)

a.
B314805

Disengage the clamp.


b.
U190261E01
0.978,0.854 1.266,1.645 false 1.201,1.662 1.354,1.809 0.152,0.146 10 *1

Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws.

Text in Illustration
*1 Protective Tape


c.

Disconnect the connector.


d.
B314804

Remove the front door outside handle assembly, as shown in the illustration.


Hide 69241H 29.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B314807

Disengage the 3 claws and remove the front door front outside handle pad.


Hide 69242E 30.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B314808

Disengage the 2 claws and remove the front door rear outside handle pad.


Hide 69202A 31.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B314809E01
0.132,0.16 0.321,0.336 0.189,0.176 10 *a 0.17,2.308 0.359,2.484 0.189,0.176 10 *b

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.

Text in Illustration
*a Outside Vehicle
*b Inside Vehicle


Hide 69312 32.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B314810E01
1.731,0.157 1.838,0.317 0.107,0.160 10 1 2.488,0.282 2.595,0.441 0.107,0.160 10 2

Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 68620 33.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B314811

Remove the bolt.


b.

Remove the 2 nuts and front door check assembly.


Hide 67001A 34.REMOVE FRONT DOOR PANEL CUSHION

a.
B314812

Disengage the 2 claws and remove the 2 front door panel cushions.


Hide 68210C 35.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 67811C 37.REMOVE FRONT DOOR HOLE COVER

a.
B314813

Disengage the 4 claws and remove the front door hole cover.