If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
Bring the electrical key transmitter sub-assembly near the front door outside handle assembly, and perform a front passenger door entry lock and unlock operation check.
| *1 | Electrical Key Transmitter Sub-assembly |
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.98 ft.) |
If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.
When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Entry functions operate abnormally | A |
| Entry functions operate normally | B |
A
B
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the F5*1 or E1*2 front door outside handle assembly (for passenger side door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-11 (CLG2) - F5-6 (ANT1) | Always | Below 1 Ω |
| D41-10 (CG2B) - F5-3 (ANT2) | Always | Below 1 Ω |
| D41-21 (POS2) - F5-5 (B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-11 (CLG2) - E1-6 (ANT1) | Always | Below 1 Ω |
| D41-10 (CG2B) - E1-3 (ANT2) | Always | Below 1 Ω |
| D41-21 (POS2) - E1-5 (B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-11 (CLG2) or F5-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| D41-10 (CG2B) or F5-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| D41-21 (POS2) or F5-5 (B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-11 (CLG2) or E1-6 (ANT1) - Body ground | Always | 10 kΩ or higher |
| D41-10 (CG2B) or E1-3 (ANT2) - Body ground | Always | 10 kΩ or higher |
| D41-21 (POS2) or E1-5 (B) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the D41 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Front Door Outside Handle assembly) |
| *b | Waveform |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F5-6 (ANT1) - F5-3 (ANT2)*1
E1-6 (ANT1) - E1-3 (ANT2)*2 |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Electrical key transmitter sub-assembly not inside vehicle 5.
Electrical key transmitter sub-assembly brought outside detection area*3 6.
All doors locked through wireless operation |
5 V/DIV., 500 ms/DIV. | Pulse generation
(See waveform) |
*1: for LHD
*2: for RHD
*3: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
OK
NG
Temporarily replace the front door outside handle assembly (for front passenger side door) with a new or known good one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).
NEXT
Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).
Entry functions operate normally.
OK
NG