Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the driver side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the lock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for driver side electrical key antenna)).

WIRING DIAGRAM

B312718E07
5.563,1.208 5.927,1.375 0.365,0.167 10 false GND 5.198,1.188 5.479,1.344 0.281,0.156 10 false D48 5.24,1.01 5.417,1.167 0.177,0.156 10 false 11 5.552,0.771 5.948,0.927 0.396,0.156 10 false TSW1 1.271,0.76 1.667,0.917 0.396,0.156 10 false TRG+ 5.198,0.76 5.469,0.917 0.271,0.156 10 false D41 5.229,0.552 5.406,0.74 0.177,0.188 10 false 20 1.76,0.646 1.938,0.833 0.177,0.188 10 false 1 5.25,1.802 6.771,2.167 1.521,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.135,1.75 2.448,2.115 2.313,0.365 10 false Front Door Outside Handle Assembly (for Driver Side Door) 0.146,1.417 0.51,1.573 0.365,0.156 10 false E1*1 0.146,1.573 0.51,1.729 0.365,0.156 10 false F5*2 0.302,2.323 1,2.5 0.698,0.177 10 false *1: for LHD 1.188,2.323 1.885,2.5 0.698,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Trigger Switch Front door outside handle assembly (for driver side) (lock sensor) / OFF or ON OFF: Front door outside handle assembly (for driver side) (lock sensor) not touched
ON: Front door outside handle assembly (for driver side) (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.



OK:

On the GTS screen, the display changes between ON and OFF as shown in the table above.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY)
a.

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the E1*1 or F5*2 front door outside handle assembly (for driver side door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
D41-20 (TSW1) - E1-6 (TRG+) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D41-20 (TSW1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
D41-20 (TSW1) - F5-6 (TRG+) Always Below 1 Ω
D48-11 (GND) - Body ground Always Below 1 Ω
D41-20 (TSW1) - Body ground Always 10 kΩ or higher




OK

4.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR)
a.

Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the E1*1 or F5*2 front door outside handle assembly connector.


*1: for LHD

*2: for RHD


c.

Using an oscilloscope, check the waveform.

U190208E01
4.227,2.691 4.413,2.852 0.186,0.161 10 *b 0.572,0.546 0.758,0.707 0.186,0.161 10 *a 2.136,0.807 2.432,0.963 0.295,0.156 10 D48 4.723,0.807 5.018,0.963 0.295,0.156 10 D41 4.035,3.856 4.389,4.012 0.354,0.156 10 GND 5.325,2.834 5.511,2.995 0.186,0.161 10 *c 4.994,3.267 5.348,2.987 5.348,2.987 5.321,3.269 false 5.309,1.707 5.398,2.141 false 5.23,2.15 5.664,2.307 0.434,0.156 10 TSW1 2.658,1.689 2.753,2.141 false 2.63,2.15 2.984,2.307 0.354,0.156 10 GND

Text in Illustration
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b Waveform
*c Driver side door lock sensor touched - -

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
D41-20 (TSW1) - D48-11 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver side door lock sensor not touched → touched


2 V/DIV., 500 ms/DIV Pulse generation
(See waveform)




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR)